... The routine returns the offset (deltaX, deltaY) from the linear grid position for a specified detector location. ... the distortion (deltaX, deltaY) at the detector location (rawX, rawY) is derived from the distortion map stored in the extension FILTER-FilterId (e.g. FILTER-U, FILTER-V, FILTER-GRISM1 etc.) ... interpolate the extracted distortion points (RAWX_OFF ,RAWY_OFF ) and calculate the distortion (deltaX,deltaY) at the requested postion (rawX, rawY) . ... deltaX, deltaY . ...

Next: Star Formation Rate and Up: No Title Previous: Calculation of Evolutionary Tracks . To start calculations, we choose the distributions of the initial binary parameters: the mass of the primary ZAMS component, , binary mass ratio, , orbital separation a . ... whereas the mass ratio distribution is not. ... The zero assumption often made is that the mass ratio distribution has a flat shape, that is binaries with a high mass ratio occur as frequently as those with equal masses. ...

... Scoring Necessary step towards more automated certification Idea: · define key QC1 parameters , check new values against trending for those · evaluate compliance: o if new within defined range, ok o if outside: nok · user may focus on nok ones, while ok is certified automatically in `confidence mode ' Required: · configure set of key parameters per product · configure comparison mode o fixed: ...

... Computing the true count rates for digital data. ... The following equation is used to find the count rate. x = ( raw counts / sample time ) . ... True count rates for digital data are corrected by using the first equation for a point source and the second for an extended source. a = ( y - pre_amp - darkrate ) / ( highvolt x pt_effic ) . ... True photocurrents (count rates for analog data) are corrected by the first equation for point sources and the second equation for extended sources. ...

... CentralProcessor 0.11 documentation . ... These parameters govern all processing used for the calibrator observation. ... The dynamic flagging step can also optionally include antenna or baseline flagging. Then the bandpass table is calculated with cbpcalibrator , which requires MSs for all beams to be given. ... Second amplitude threshold applied when flagging 1934 data [hardware units - before calibration] . ... Name of the CASA table used for the bandpass calibration parameters. ...

. This quantity is the physical maximum velocity rotation corrected for inclination, expressed in km/s. It is deduced from the parameter vmaxg after correcting for inclination using incl . This rotation velocity is calculated from both the 21-cm line widths at different levels and/or the available rotation curves (generally H_alpha rotation curves). The rotation of the stellar component is given in the parameter vmaxs . HyperLeda . Questions: prugniel@obs.univ-lyon1.fr

... The models provided are: . abs - absorption of x-rays by neutral gas with solar abundances. parameter 1 = . ... parameter 2 = . ... normalization - logarithmic value of the flux density at 1 keV in units of keV cm -2 s -1 keV -1 . ... normalization - logarithmic value of the normalization of the gaussian in units of keV cm -2 s -1 . ... absorption ( params )* model ( params ) . ... A single value for the normalization (i.e., fixed normalization) will force the program to use that value. ...

System parameters on Digital UNIX . ... Digital and Cray use the number of bytes as the KIND -parameter. ... LOGICAL Default byte word KIND number = 4 1 4 LOGICAL Default double quad KIND number = 4 8 16 INTEGER int15 int31 int63 KIND number = 2 4 8 digits = 15 31 63 radix = 2 2 2 range = 4 9 18 huge = 32767 2147483647 9223372036854775807 bit_size = 16 32 64 REAL single double quad KIND number = 4 8 16 digits = 24 53 113 maxexponent = 128 1024 16384 minexponent = -125 -1021 -16381 ...

... We demonstrate through numerical simulations that model parameters estimated with our technique are essentially bias-free, even when the average number of counts per bin is 1. ... The IW technique avoids such biases by estimating through successive iterations, where for each iteration, j, , and the best-fit parameters are determined by minimization of . ... In our sample, we find that the minimum values and best-fit parameters converge after about 6 iterations. ...