... HST Phase II Proposal Instructions for Cycle 20 > Chapter 13: Wide Field Camera 3(WFC3) > 13.1 Introduction to WFC3 . ... More complete descriptions of Instrument Configurations, Modes, Apertures, Spectral Elements, Detector Characteristics, etc. are available in the WFC3 Instrument Handbook . ... Table 13.1 lists the permitted WFC3 Instrument Configurations, Operating Modes, Apertures, Spectral Elements, and Optional Parameters. ... Optional Parameters . ... See Table 13.2: Apertures for WFC3/UVIS ...

... The following document provides a short instruction on the reduction of synthesis observations with the WSRT using AIPS. ... The aim of the instructions below is to provide a check list of reduction steps to be taken and of the important parameters to be set in each task. ... Please consult the AIPS Cookbook for detailed information about data reduction with AIPS (and various Banana recipes). TASK 'FITLD' . ... GETN n . ... TGET 'INDXR' . ... DOCAL 1 . ... GAINU 2 . ... IMAGRPRM 0 . ...

... A file upload element on an HTML form. ... JavaScript 1.1: added type property . ... The HTML INPUT tag, with "file" as the value of the TYPE attribute. For a given form, the JavaScript runtime engine creates appropriate FileUpload objects and puts these objects in the elements array of the corresponding Form object. ... form . ... For all FileUpload objects, the value of the type property is "file" . ... Use the value property to obtain the file name that the user typed into a FileUpload object. ...

... This is done by taking in all input files the extension whose name is specified by the maintable parameter (called 'merged extension' in what follows) and merging the columns into a single output extension of the same name. ... Its contents is taken from the CCDID keyword (and QUADRANT for EPIC PN). ... To propagate other column specific keywords, they must be specified manually via the extensionchecks , mainattributes , maxattributes and minattributes parameters (see above). ...

... Average resolution at altitude H=668 km . ... Swath width at H=668 km and inclination of beginning of swath 20.48 degrees . ... Resolution at H=668 км . ... Наименование параметра . ... 1 канале . ... Полоса обзора при H=668 км . ... 1-5 спектральной зоне, не более . ... 1 спектральной зоне . 0,48-0,52 мкм . ... 0,915-0,997 мкм . ... 1-4 канал . ... 1-4 каналов . ... Спектральные характеристики каналов (по уровню 0,5): . ... For more information send a mail to: info@sputnik.infospace.ru . ...

The Agile window provides complete control over the Agile high-speed photometer. ... All other parameters are specified as part of the command that starts an exposure sequence. ... To connect the filter wheel controller, issue this command in the command bar at the bottom of the Log window: agile connDev fw . ... To home the filter wheel controller, issue this command in the command bar at the bottom of the Log window: agile fwhome (there must be a filter wheel mounted in Agile for homing to succeed). ...

... The instrument modes and arms should be indicated and described, and the keywords that distinguish between different modes should be indicated (usually INS.MODE is used if it is a mode and OCS keys are used in case it is related to an arm). ... Raw frames The format of the raw frames for each mode and arm should be described. ... The design should be checked on pre-processing or processing, which involves products only (no trigger via raw frames). ... QC parameters. ...

... Meade Instruments Corporation . ... 505 Connector Cable Set . Operating Instructions for use with the Meade? Autostar? ... The #505 Connector Cable Set provides access to three Autostar operations: . ... 2: #505 Connector Cable Set connects between two Autostar handboxes. (1) 3-foot cable. ... If you have a question concerning use of the #505 Connector Cable Set, call the Meade Instruments Customer Service Department at (949) 451-1450, or fax at (949) 451-1460. ... Autostar Downloads . ...

... Second, the observatory can control the configuration, test data analysis procedures, and provide calibration solutions with the help of instrument models. This paper presents the VLT object-oriented framework for the development of ETCs (Exposure Time Calculators) and data simulators. ... Instrument simulations are being developed for the purpose of predictive calibration, instrument configuration control, and evaluation of data analysis procedures. ...

DIGITAL WDC EXCHANGE FORMAT . FOR OBSERVATORY 1.0 MINUTE VALUES 1. ... DATA-1 .. DATA-60 are 1-minute values of the given element for that hour. ... Typically, digital 1-minute values received by WDCs from organizations operating automatic magnetic observatory instruments are averages of more frequendy sampled values, e.g. 10-second point samples. ... If the method used to obtain 1-minute average values is important to a user, the WDC will assist in determining the exact procedure applied. ...

Following designations of elements/ parameters are used in AMPLE. ... mean anomaly . ... Node . ... Apart conventional orbital elements AMPLE gives possibility to calculate for each minor planet the following often used functions: . ... MOID . ... To calculate MOID user should order the name or the number of the major or minor planet through dialog. ... To calculate CT user should order the name or the number of the major or mino