Documentation for Delay Line Final Design Review - 12 Feb 2008 Notes: Anything marked in Status as [TBU] is definitely `To Be Updated' `Expected Date' refers to the expected date of release where this is likely to be different from the due date. ... TBU] INT-406-VEN-0112 MF/RCB/DMAW/EBS 22 Jan 08 22 Jan 08 Released. ... MF/XS/DMAW MF MF MF MF/XS/DMAW 22 Jan 08 29 Jan 08 Yet to be drafted 22 Jan 08 22 Jan 08 Yet to be drafted 22 Jan 08 22 Jan 08 Released. ... Document No. ...

... It lists the coefficients defining the colour transformations, the zero points for the different filters and the aperture radii used in the photometric calibration analysis. ... The AB system zero point of the filter FilterID is stored in the keyword ABM0 FilterID , e.g. the AB zero point of the the U-filter is stored in ABM0U. The flux conversion factor derived from White Dwarfs of the filter FilterID is stored in the keyword FCF FilterID . ... description . ... AB Flux conversion factor of U . ...

... It includes level converters and a optional radio modem designed to decode the radio timecode signals transmitted by the Canadian time and frequency station CHU. A complete set of schematics, PCB artwork, drill templates is in the pub/ntp/gadget.tar.Z file on ftp.udel.edu. ... One of these converts a TTL positive edge into a fixed- width pulse at EIA levels and is for use with a timecode receiver or oscillator including a TTL PPS output. ... See the schematic diagram gadget.s01 for reference. ...

... Created: 23 February 2001 . ... SOFTWARE MAINTENANCE MANUAL . ... 9 January 2001 . ... Note: in the final document, the table of contents will be to third level] . The Software Maintenance Manual describes the procedures for installation and maintenance of the software for the Gemini Near-infrared Integral Field Spectrograph (NIFS). ... Section 19.4.3 of the document “Programmatic Requirements for Gemini Instrumentation Development” states the requirements for the Software Maintenance Manual . ...

... Status of the ELECTRON experiment . ... The objective of the ELECTRON experiment is to perform 3-D measurements of the plasma electrons in the energy range from 10 eV to 26000 eV, with good angular resolution, sensitivity and large dynamical range. ... Figure 1 presents the ELECTRON sensor. ... Click on the picture to view large one) . ... Figure 3 shows dynamical spectra with counting rate measurements performed by ELECTRON experiment during very multiple magnetopause crossings on February, 4, 1996...

... SFIT is a general-purpose code designed to optimize theoretical stellar spectra to an observed spectrum. ... While the programme expects input from "stdio", it is more natural to save commands in a file (eg "sfit_input") and run the code simply by . ... If the spectra to be fitted have a filename "star_spectrum", then the best fit spectrum will be written out, together with the renormalized input spectrum, to a file called "star_spectrum.fit". ... sets up model spectrum grid (and for 2nd star) . ...

... Fasti is a controller architecture originally developed for fast infrared astronomical array detectors, and intended to be powerful and extendible. ... 2002), Foppiani et al. 2002)). ... The parallel input interface (now a commercial board). ... Esposito, S., Riccardi, A., Storm, J., Accardo, M., Baffa, C., Biliotti, V., Foppiani, I., Puglisi, A., Ragazzoni, R., Ranfagni, P., Stefanini, P., Salinari, P., Seifert, W., Storm, J. 2002, SPIE Conference AS06, Wizinowich, P. L. Ed., in press . ...

The optical scheme of the instrument is sketched in Figure 1 , it is designed to match the F/20 focal ratio of the TIRGO telescope. We have, following the optical path, the window of the dewar, the order sorting filter (not in figure), a field lens, in Calcium Floride, and the slit, in the focal plane of the telescope. ... The resolving power is (for first order of grating) of about 600 in the center of J band and 950 in the center of the K band, using a slit of two pixel (3.46 arcsec). ...

... This tool is designed to create formatted and unformatted file-by-file reports from fits headers, or fits files. fitsreport reads from a configuration file all the keys to be displayed: . ... retrieve non-FITS information (file name, path name). ... The tool reads all fits files in the given path, evaluates the configuration file fitsreport_raw.cfg (to be in ${DFO_CONFIG_DIR}) and dumps the output into out. ... This is more evident in the other config file, fitsreport_raw.cfg. ...