Instructions for ftp-submission of postscript [.ps] or PDF [.pdf]
files
If you choose to do your POSTSCRIPT/PDF SUBMISSION via ftp, then
please follow these instructions:
Set the COVERPART KEYWORD "\formattedsubmission{FTP}" in your proposal.
Ftp to ftp-presto.stsci.edu, login as anonymous, give your complete
email address as password, cd to "upload", put your PostScript or PDF
file there, and logout again with "bye". For example:
* ftp ftp-presto.stsci.edu
Connected to CLOTHO.STSCI.EDU.
220 clotho.stsci.edu FTP server (Version wu-2.4(13) ready.
* Name (ftp-presto.stsci.edu:blacker): anonymous
331 Guest login ok, send your complete e-mail address as password.
* Password: blacker@stsci.edu [password will not be echoed]
230 Guest login ok, access restrictions apply.
* ftp> cd upload
250 CWD command successful.
* ftp> put bblacker_1.ps [regarding name, see note below]
200 PORT command successful.
150 Opening ASCII mode data connection for bblacker_1.ps.
226 Transfer complete.
local: bblacker_1.ps remote: bblacker_1.ps
22 bytes sent in 0.0012 seconds (17 Kbytes/s)
* ftp> bye
221 Goodbye
[* denotes a line where you enter either response or command]
Email the LaTeX coverpage to newprop@stsci.edu. If you have set \formattedsubmission{FTP}
on the coverpage we will then go and retrieve your PostScript or
PDF file.
You will receive an acknowledgement (generally within two days) that
your PostScript or PDF file has successfully printed. The submission is not
considered complete until such an acknowledgement has been sent. If
you fail to receive an acknowledgement within one week, then please
contact the STScI Help Desk (see contact address below).
Important Notes:
The data area where you put your file is a high security area. Hence
you will neither be able to list the contents of the directory, nor
to copy any file from there even if you know its name. Hence, do not
worry that you cannot see your file there; if "ftp" has answered
"transfer complete" then your file has arrived safely.
To make it possible for us to locate your file,
please adopt the following naming convention for your file. The
filename should be:
'first name initial' 'last name' '_' 'identifier' '.ps', where
'identifier' can be any string.
It is just meant to make the
filename unique in case you have more than one proposal or in case
of transfer errors. Say your name is Isaac Newton, and this is your
third proposal, so you choose 'No3' as identifier. Your
filename is then: inewton_No3.ps
Fixes to Anticipated Problems:
You forget to set the correct COVERPAGE KEYWORD.
FIX: The "formattedsubmission{}" KEYWORD is there to make it possible
for us to locate your formatted proposal, and match it up with the
coverpage. If you find that you by mistake had set the wrong KEYWORD,
please contact the STScI Help Desk (see contact
address below) and supply the information needed (PI name and
proposal title) to link your coverpage to your proposal.
The ftp link goes down in the middle of a transmission, and you are not
sure the transfer was complete. You cannot check if it was, because
the high security ftp area will not allow you to do that.
FIX: Change the identifier part of your filename ONLY. Say by
incrementing a counter. In the example above you could choose:
inewton_No3.ps ---> inewton_No4.ps or
inewton_No3.ps ---> inewton_No3a.ps
if you do not want to change the number specification. Then ftp it
again.
Your Contact at STScI:
STScI Help Desk
Attention: Science Programs Selection Office
Phone: [1] 410-338-1082 or 1-800-544-8125 (toll free U.S. number)