Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.stecf.org/conferences/adass/adassVII/lindep.html
Дата изменения: Mon Jun 12 18:51:56 2006 Дата индексирования: Mon Oct 1 23:38:25 2012 Кодировка: Поисковые слова: п п п п п п п п п п п п п |
Next: The Distributed Analysis System Hierarchy (DASH) for the
SUBARU Telescope
Up: Dataflow and Scheduling
Previous: System Interfaces to the STIS Calibration Pipeline
Table of Contents -- Index -- PS reprint -- PDF reprint
P. Linde
Lund Observatory, Box 43, SE-221 00 Lund, Sweden, Email: peter@astro.lu.se
F. Pasian and M. Pucillo
Osservatorio Astronomico, Via G.B.Tiepolo 11, I 34131 Trieste,
Italy , Email: {pasian,pucillo}@ts.astro.it
J. D. Ponz
ESA Villafranca P. O. Box 50727, 28080 Madrid, Spain,
Email:jdp@vilspa.esa.es
As a response to the increasing need for remote control of large scientific installations, the REMOT (Remote Experiment MOnitoring and conTrol) project was initiated in 1995. The final goal of the project is to develop and validate a generic approach to allow real time operation and multimedia information feedback, using communications infrastructure available to European researchers.
Funded through the European Union Telematics Organisation, the project involves representatives from the astro- and plasma physics communities and from several teleoperation and software design institutes and companies. The partners from the astrophysical community include OAT (Italy), IAC (Spain), LAEFF (Spain), Nordic Optical Telescope and CDS (France).
The design of the generic system and communications architecture started by creating a large database of user requirements, collected from each participating partner. The requirements were derived from the following operational scenario:
The services that REMOT will provide can be roughly divided into four categories:
Analysis of the collected database of requirements resulted in a set of service definitions. These services will be implemented by using two different conceptual planes (see Figure 1). These are (1) the System Plane, supporting Quality of Service (QoS), (2) the Management Plane, supporting reliable communications. Operational services will be performed in the System Plane and managed over the Management Plane, while auxiliary services will be supported over the Management Plane.
![]() |
For the communications architecture we use a CORBA compliant mechanism: the Management Plane is implemented by using CORBA and its IP-based layer (IIOP) directly. When QoS is required (System Plane), a bridging mechanism bypassing IIOP can be used, or alternatively there is the possibility of using the transport services directly. The presence of a Communications Manager to arbitrate communication resources is necessary in both cases.
Galileo's high-level control system is based on a distributed computer architecture in which both the code and the data are shared by all the workstations supporting the systems (Pucillo 1994). Remote control is implicitly embedded in the design, since the control workstation can either be located or be connected via a bridge or a router.
REMOT improves this remote access philosophy since, besides using a common user interface for different telescopes, it does not require TNG-specific hardware, but will allow remote observations to be run ``at the astronomer's own desk", on a simple PC.
Integrating the control system of the Galileo telescope in the REMOT project is simple:
The software interface between the control system and REMOT consists of an ancillary process running under the same environment. This process is also responsible for retrieving from the TNG on-line database the updated status of the system, and for downloading observational data in original (FITS) or compressed (quick-look) format to the remote user.
A prototype of the complete system is under development, including the basic services. Since REMOT is limited in scope, only a subset of the design will be currently implemented. This will, however, allow a practical demonstration to be performed using the new Galileo telescope located at La Palma and the IAC 80 cm telescope located on Tenerife.
REMOT will be extended in a continuation project DYNACORE, where a
complete implementation is targeted. The design will then be upgraded
to include real time access to data bases, flexible scheduling and
dynamic reconfiguration. Additional information on the project can be
found at
http://www.laeff.esa.es/~tcpsi/
.
Pucillo, M. 1994, Handling and Archiving Data from Ground-Based Telescopes, M.Albrecht & F.Pasian eds., ESO Conferences and Workshop Proceedings, Vol. no. 50, 77
Next: The Distributed Analysis System Hierarchy (DASH) for the
SUBARU Telescope
Up: Dataflow and Scheduling
Previous: System Interfaces to the STIS Calibration Pipeline
Table of Contents -- Index -- PS reprint -- PDF reprint