Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.sai.msu.su/~er/xntp/howto.html
Дата изменения: Unknown Дата индексирования: Sat Dec 22 01:43:37 2007 Кодировка: Поисковые слова: п п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п |
Reference clock support maintains the fiction that the clock is actually an ordinary peer in the NTP tradition, but operating at a synthetic stratum of zero. The entire suite of algorithms used to filter the received data, select the best clocks or peers and combine them to produce a local clock correction are operative as with ordinary NTP peers. In this way, defective clocks can be detected and removed from the peer population. As no packets are exchanged with a reference clock, however, we replace the transmit, receive and packet procedures with separate code to simulate them.
Radio and modem reference clocks by convention have addresses in the
form 127.127.t.u,
, where t is the
clock type and u in the range 0-3 is used to distinguish multiple
instances of clocks of the same type. Most clocks require a serial port
or special bus peripheral. The particular device is normally specified
by adding a soft link /dev/devicedd
to the
particular hardware device involved, where d
corresponds to the unit number.
The best way to understand how the clock drivers work is to study the
ntp_refclock.c
module and one of the drivers already
implemented, such as refclock_wwvb.c
. Routines
refclock_transmit()
and refclock_receive()
maintain the peer variables in a state analogous to an actual peer and
pass received data on through the clock filters. Routines
refclock_peer()
and refclock_unpeer()
are
called to initialize and terminate reference clock associations, should
this ever be necessary. A set of utility routines is included to open
serial devices, process sample data, edit input lines to extract
embedded timestamps and to perform various debugging functions.
The main interface used by these routines is the
refclockproc
structure, which contains for most drivers the
decimal equivalents of the year, day, month, hour, second and
millisecond/microsecond decoded from the ASCII timecode. Additional
information includes the receive timestamp, exception report, statistics
tallies, etc. In addition, there may be a driver-specific unit structure
used for local control of the device. The support routines are passed a
pointer to the peer
structure, which is used for all peer-
specific processing and contains a pointer to the
refclockproc
structure, which in turn contains a pointer to
the unit structure, if used. A table typeunit[type][unit]
contains the peer structure pointer for each configured clock type and
unit.
Many drivers support the tty_clk
and/or
ppsclock
line disciplines or streams modules described in
the included in the Line Disciplines and Streams
Modules page. The tty_clk
module reduces latency errors
due to the operating system and serial port code in slower systems. The
ppsclock
module is an interface for the PPS signal provided
by some radios. It can be connected via a level converter/pulse
generator described in the Gadget Box PPS Level
Converter and CHU Modem page.
By convention, reference clock drivers are named in the form
refclock_xxxx.c
, where xxxx is a unique
string. Each driver is assigned a unique type number, long-form driver
name, short-form driver name, and device name. The existing assignments
are in the Reference Clock Drivers page
and its dependencies. Drivers are conditionally compiled using a unique
flag string in the CLOCKDEFS
line described in the Configuration Options page.
The standard clock driver interface includes a set of common support
routines some of which do such things as start and stop the device, open
the serial port, and establish special functions such as PPS signal
support. Other routines read and write data to the device and process
time values. Most drivers need only a little customizing code to, for
instance, transform idiosyncratic timecode formats to standard form,
poll the device as necessary, and handle exception conditions. A
standard interface is available for remote debugging and monitoring
programs, such as ntpq
and xntpdc
, as well as
the filegen
facility, which can be used to record device
status on a continuous basis.
The interface code and this documentation have been developed over some time and required not a little hard work converting old drivers, etc. Should you find success writing a driver for a new radio or modem service, please consider contributing it to the common good. Send the driver file itself and patches for the other files to Dave Mills (mills@udel.edu).
A new reference clock implementation needs to supply in addition to the driver itself several changes to existing files.
./include/ntp.h
REFCLK_xxxx
identification code should be recorded in the list opposite its assigned
type number.
./lib/clocktypes.c
./lib/clktype
array is used by certain display
functions. A unique short-form name of the driver should be entered
together with its assigned identification code.
./xntpd/ntp_control.c
clocktypes
array is used for certain control
message displays functions. It should be initialized with the reference
clock class assigned to the driver, as per the NTP specification
RFC-1305. See the ./include/ntp_control.h
header file for
the assigned classes.
./xntpd/refclock_conf.c
refclock_conf
array is a set of pointers to transfer vectors in the individual
drivers. The external name of the transfer vector should be initialized
in correspondence with the type number.
refclock_newpeer
- initialize and start a reference
clock
refclock_unpeer
- shut down a clock
refclock_transmit
- simulate the transmit procedure
refclock_sample
- process a pile of samples from the
clock
fudgetime1
can be added to the final offset to compensate
for various systematic errors. The routine returns one if success and
zero if failure due to invalid timecode data or very noisy offsets.
Note that no provision is included for the year, as provided by some (but not all) radio clocks. Ordinarily, the year is implicit in the Unix file system and hardware/software clock support, so this is ordinarily not a problem. Nevertheless, the absence of the year should be considered more a bug than a feature and may be supported in future.
refclock_receive
- simulate the receive and packet
procedures
refclock_gtlin
- groom next input line and extract
timestamp
tty_clk
line
discipline/streams module, it returns that as the timestamp; otherwise,
it returns the buffer timestamp. The routine return code is the number
of characters in the line.
refclock_open
- open serial port for reference clock
refclock_ioctl
- set serial port control functions
termios
), SYSV
(termio
) and BSD (sgtty
) interfaces with
varying degrees of success. The routine sets up the tty_clk,
chu_clk
and ppsclock
streams module/line discipline,
if compiled in the daemon and requested in the call. The routine returns
one if success and zero if failure.
refclock_control
- set and/or return clock values
fudgetimes, fudgevalues,
reference ID and stratum.
refclock_buginfo
- return debugging info
xntpdc
and the clkbug
command.