Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.naic.edu/~phil/hardware/vertex/sharemegsvertex/lcu/pcr/dos/SCANDISK.INI Дата изменения: Wed Mar 7 01:04:42 2001 Дата индексирования: Thu Jan 15 10:44:02 2009 Кодировка: Поисковые слова: zodiacal light

; SCANDISK.INI
;
; This file contains settings you can use to customize the ScanDisk program.


; -------------------------------------------------------------------
; The [ENVIRONMENT] section contains the following settings, which
; determine general aspects of ScanDisk's behavior:
;
; Display Configures ScanDisk to run with a particular type of
; display. The default display type is Auto (ScanDisk
; adjusts to the current display).
;
; Mouse Enables or disables mouse support. The default value is On.
;
; ScanTimeOut Determines whether ScanDisk should detect disk timeouts
; while performing a surface scan. The default value is Off.
;
; NumPasses Determines how many times ScanDisk should check each
; cluster during a surface scan. The default value is 1.
;
; LabelCheck Determines whether ScanDisk should check volume labels
; for invalid characters. The default is Off.
;
; LfnCheck Enables support for long filenames. The default value is On.
; If LfnCheck is On, ScanDisk leaves any long filenames
; unchanged. If LfnCheck is Off, ScanDisk validates
; all filenames, including long filenames, to ensure that
; they conform to the "8.3" file-naming convention used by
; MS-DOS versions 6.22 and earlier.
;

[ENVIRONMENT]
Display = Auto ; Auto, Mono, Color, Off
Mouse = On ; On, Off
ScanTimeOut = Off ; On, Off
NumPasses = 1 ; 1 through 65,535 (anything over 10 is slow)
LabelCheck = Off ; On, Off
LfnCheck = On ; On, Off

; -------------------------------------------------------------------
; The [CUSTOM] section determines ScanDisk's behavior when ScanDisk is
; started with the /CUSTOM switch. You can adjust these settings to
; create a customized "version" of ScanDisk. This can be especially
; useful for running ScanDisk from a batch file. The [CUSTOM] settings are:
;
; DriveSummary Determines whether ScanDisk displays full-screen
; summary information after checking each drive.
; The default is Auto (ScanDisk displays the summary
; only if it encounters errors on that drive).
;
; AllSummary Determines whether ScanDisk displays full-screen
; summary information after checking all drives.
; The default is Auto (ScanDisk displays the summary
; only if it encounters errors on any drive).
;
; Surface Determines whether ScanDisk will perform a surface scan:
; Never (Default) Does not perform a surface scan.
; Always Performs a surface scan without prompting first.
; Prompt Prompts before performing a surface scan.
; The /SURFACE command-line switch overrides this setting.
;
; CheckHost Determines whether ScanDisk will first check a host drive
; before checking any compressed drives located on that drive.
; Never (Default) Does not check the host drive.
; Always Checks the host drive without prompting first.
; Prompt Prompts before checking the host drive.
;
; SaveLog Determines what ScanDisk does with the repair log file:
; Off (Default) Does not save the repair log.
; Append Appends the log to the previous log, if any.
; Overwrite Replaces the previous log with the new log.
;
; Undo Determines whether ScanDisk creates an Undo floppy disk.
; The default is Never (ScanDisk does not create an Undo disk).
; The Prompt value causes ScanDisk to prompt you for a disk.

[CUSTOM]
DriveSummary = Auto ; Auto, On, Off
AllSummary = Auto ; Auto, On, Off
Surface = Never ; Never, Always, Prompt
CheckHost = Never ; Never, Always, Prompt
SaveLog = Off ; Off, Append, Overwrite
Undo = Prompt ; Prompt, Never

; The following settings determine the corrective action ScanDisk will
; take if it was started with the /CUSTOM switch and finds a disk error.

; The next five settings accept any of the following values:
; Prompt Causes ScanDisk to prompt you before fixing this problem.
; Fix Causes ScanDisk to fix the problem without prompting you.
; Quit Causes ScanDisk to terminate if it encounters this problem.

DS_Header = Prompt ; Damaged compressed volume file header
FAT_Media = Prompt ; Missing or invalid FAT media byte
Okay_Entries = Prompt ; Damaged, but repairable, directories/files
Bad_Chain = Prompt ; Files or directories which should be truncated
Crosslinks = Prompt ; FAT-level crosslinks


; The next seven settings accept any of the following values:
; Prompt Causes ScanDisk to prompt you before fixing this problem.
; Fix Causes ScanDisk to fix the problem without prompting you.
; Quit Causes ScanDisk to terminate if it encounters this problem.
; Skip Causes ScanDisk to skip fixing this problem, but continue
; checking the disk.

Boot_Sector = Prompt ; Damaged boot sector on compressed drive
Invalid_MDFAT = Prompt ; Invalid MDFAT entries
DS_Crosslinks = Prompt ; Internal (MDFAT-level) crosslinks
DS_LostClust = Prompt ; Internal lost clusters
DS_Signatures = Prompt ; Missing compressed volume file signatures
Mismatch_FAT = Prompt ; Mismatched FATs on non-compressed drives
Bad_Clusters = Prompt ; Physical damage or decompression errors


; The next setting accepts any of the following values:
;
; Prompt Causes ScanDisk to prompt you before fixing this problem.
; Delete Causes ScanDisk to delete the damaged directory entries
; without prompting you first.
; Quit Causes ScanDisk to terminate if it encounters this problem.

Bad_Entries = Prompt ; Damaged and irrepairable directories or files


; The next setting accepts any of the following values:
;
; Prompt Causes ScanDisk to prompt you before fixing this problem.
; Save Causes ScanDisk to save the lost clusters as files in the
; root directory without prompting you first.
; Delete Causes ScanDisk to delete the contents of the lost clusters
; without prompting you first.
; Quit Causes ScanDisk to terminate if it encounters this problem.
; Skip Causes ScanDisk to skip fixing this problem, but continue
; checking the disk.

LostClust = Prompt ; Lost clusters