Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.naic.edu/~phil/td/td.html
Дата изменения: Fri Jan 15 16:23:24 2016 Дата индексирования: Sun Apr 10 02:04:15 2016 Кодировка: Поисковые слова: rigel |
page |
description |
0 |
ctrl cabinet layout |
1 |
breakers |
2 |
ladder logic |
3 |
watchdog |
4 |
brakes |
5 |
ldCells,load
metering,autorelease |
6 |
fans |
7 |
little start computer |
8 |
pcu |
9 |
grounding |
com |
communications |
mot |
motor installation |
dio_1 dio_2 |
digital i/o boards |
td12 |
td 4 |
td8 |
|
power @box b1 cable 5
in control room |
|||
power @ box 12-7 before
patch to each huffman box (n) is fiber number in 12-7 |
-17.8 (3) |
-17.3 (5) |
-18.5 (4) |
power @ 1 sec tick
rcvr |
-18.6 |
-18.1 |
-19.8 |
td/date | jack flim |
sw final limit | prelimit | tapeMeas inch / bar (when enc=13") |
12 | (24+,.313) (24+,.253) |
(23.290,1.150) 23apr12 (23.36,1.2) 04feb09 (23.28,0.86) 14aug06 (23.28,0.86) 17mar06 (23.21,1.19) 04aug03 |
(22.278,1.780) 23apr12 (22.92,1.81) 04feb09 (22.461,1.668) 14aug06 lost .3"!! (22.69,1.57) 17mar06 (22.62,1.9 ) 04aug03 |
28 1/8 (enc=12")23apr12 26 19/16 04feb09 26 3/8" 18mar05 |
4 |
(24+,.799) |
(23.317,1.487)
24sep12 (23.19,1.37) 13may04 |
(22.78,2.03) 24sep12 ( 22.82,2.01) 13may04 |
bar=11.01 " |
8 | (23.21,1.19) 30jul03 | (22.5,1.9) 30jul03 | 25 15/16 18mar05 |
There is a pre and final hardware limit switch for the upper limit and the lower limit on each jack. The actions of the limts are:
Whenever we survey from AO9, we use the current encoder values to determine how to move the tiedowns. So by definition, after an ao9 survey, the tiedown positions are now correct. This is not quiet true since we have been using the focus curves to determine the focus rather than the ao9 survey value.
The table below has the measured values of the position using encoder and tape measure. Encoder values 24 inches is when the jack is fully retracted (high tension). 0 encoder inches is when the jack if fully extended (low tension).The cols in the table below are:
date/jack |
encoder |
notes |
td4-21sep12 |
11.01 inces |
bar on center bolt. |
td12 -23apr12 |
11.692 inches |
bar on center bolt, north
side (see photos below) |
The software limits used to limit the
requested positions are .2 inches inside the final limits. They
are in the file /home/phil/h/tieProg.h
start date | td12 | td8 | td4 |
08feb00 | (22.29,1.43) | (22.87,1.93) | (22.20,1.19) |
xxx | (21.79,1.2) | (22.14,1.52) | (23.21,1.95) |
In the table below:
amp 1 is the
top amplifier
amp 2 is the bottom
amplifier
cable 1 normally goes
to the top amp
cable 2 normally goes
to the bottom amp
see the drawing in the td manual for where the load cell is
located on the yoke.
To do the measurement:
td,ldcell,cable | Ex+ to Sig- |
Ex+ to Sig+ |
Ex-to Sig- |
Ex- to Sig+ |
date |
8-2 ,90459 | 269.33 |
268.60 |
268.10 |
268.70 |
13jan16 (2) |
12-1,90408 |
267.6 |
267.9 |
267.9 |
267.7 |
9jun11 |
12-2,90409 |
267.5 |
267.2 |
268.4 |
267.5 |
9jun11 |
8-1 ,90407 |
268.1 |
268.8 |
268.6 |
268.6 |
9jun11 |
8-2 ,90459 |
268.8 |
268.8 |
268.4 |
268.5 |
9jun11 |
12-1,90408 | 289.7(1) | 268.6 | 267.6 | 267.5 | 09nov06 (1) |
12-1,90408 | 267.9 | 268.4 | 267.6 | 267.9 | 17jan05 |
12-2,90409 | 264.2 | 264.4 | 264.5 | 264.5 | 09nov06 |
12-2, 90409 | 267.1 | 267.5 | 268.2 | 268.1 | 17jan05 |
4-1,90401 | 267.8 | 268.2 | 267.8 | 268.2 | 02sep05++ |
4-1,90410 | 267.3 | 268.7 | 267.8 237.4** |
267.5 | 17jan05 |
4-1,90410,1 | 268.4 | 267.7 | 268.9 | 270.4 | 31oct01 |
4-2,90458 | 264.8 | 264.9 | 264.9 | 265.1 | 02sep05++ |
4-2,90458 | 264.2 | 264.3 | 264.7 | 264.7 | 17jan05 |
4-2,90458 | 264.5 | 264.6 | 264.9 | 265.0 | 31oct01 |
8-1,90407 | 268.2 | 269.6 357.6** |
268.8 | 269.7 | 02sep05 ++ with filter |
8-1,90407 | 268.1 | 267.9 | 268.3 | 268.3 | 17jan05 |
8-1 ,90407,1 | 268.0 | 268.3 | 269.1 | 269.3 | 31oct01 |
8-2,90459 | 268.6 | 268.6 | 268.1 | 268.2 | 02sep05 ++ |
8-2,90459 | 268.7 | 268.6 | 268.6 | 268.3 | 17jan05 |
8-2,90459,2 | 268.5 | 267.4 | 268.2 | 268.3 | 31oct01 |
8-2,90459,1 When db25 filter bad |
264.2 | 352.3 ** | 352.4** | 268.2 | 31oct01 |
The values with ** had bad filters in the db25 connector.
++ removed the filter because it was bad (and had no spares)
date |
td12-1 |
td12-2 |
td4-1 |
td4-2 |
td8-1 |
td8-2 |
09jun11 (1) |
147697 (90408) |
replaced with?? (90409) |
90410 |
09458 |
90407 |
90459 |
06oct09 |
147697 |
replaced with ?? |
90410 |
09458 |
90407 |
|
23jun08 |
147697 | 207629 |
90410 | 90458 | 90407 | 90459 |
14nov06 |
147697 |
90409 | 90410 | 90458 | 90407 | 90459 |
14aug98 |
90408 |
90409 |
90410 |
90458 |
90407 |
90459 |
xxjan16 (2) |
90408 | 90409 | 90410 | 90458 | 90407 | 253850 |
date |
tieRefUsed [td12,4,8] |
tdAutoTrk.h |
Offsets |
Notes |
07apr07 |
14.9276,15.4311,12.3753 |
14.875,14.616,13.243 | .05257,.81511,-.8677 |
lead from corners, laser
shack removed. Painting project weight on platform. |
06dec07 |
15.1140,15.7028,11.9171 | 14.875,14.616,13.243 | .2390,1.0868,-1.3259 |
after 06dec07 tilt run.
Painting project weight off platform. |
09dec07 |
15.1140,15.2028,15.1670 | 14.875,14.616,13.243 |
.2390,.5868,1.9241 |
After td nuts moved to
equalize td positions. |
10dec07 |
15.0718,15.3196,15.0926 |
14.875,14.616,13.243 |
.1968,.7036,1.8496 |
Updated using the first two
aswings done on 10dec07. |