Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.issp.ac.ru/lrfs/technology/icm_en.htm
Дата изменения: Tue Feb 14 15:59:18 2006 Дата индексирования: Tue Oct 2 06:37:21 2012 Кодировка: Поисковые слова: universe |
Internal crystallization method
Single-crystalline
eutectic oxide fibres are needed to reinforce metal,
intermetallic and ceramic matrices to obtain high temperature composites.
The method of internal
crystallization was developed in Laboratory of Reinforced Systems of Solid
State Physics Institute initially to produce oxide-matrix/molybdenum-matrix
composites, which were considered mainly as model ones. The concept of the
method is illustrated in Figure 1.
Figure 1. Schematic of the
internal crystallization method (ICM).
First of all a molybdenum
carcass with continuous cylindrical channels is obtained by diffusion bonding
of an assemblage of molybdenum wires and foils. The carcass is then put into
contact with an oxide melt; capillary forces yield the infiltration of the
channels with a melted fibre material. The oxide/molybdenum block is then
moved to a cold zone of the furnace to crystallize the fibres. This is the
basic scheme of the ICM [5 ,6], a variation of the basic scheme with single
crystalline seeds at the top of the carcass (Figure
2) allows obtaining a fibre set of a homogeneous crystallographic
orientation [8]. The final step in the obtaining fibres process is dissolution
of molybdenum in an HCl/HNO3/H2O mixture.
Figure 2.
A set of the molybdenum
carcasses with seeds at the top.
A variety of the oxide fibres,
such as sapphire [8 ] and YAG [9 ] of a homogeneous crystallographic
orientation alumina-YAG eutectic [7 ], and single crystalline mullite [10 ]
have been obtained by using the method.
Some illustrations of the fibres obtained are presented in
Figure 3
.
A bounded
bundle of sapphire fibres.
A bounded
bundle of sapphire fibres.
Sapphire fibres photographed in polarised light.
Single crystalline yttrium-aluminium
garnet (YAG) fibre
Mullite fibres photographed in
polarised light.
Figure 3.
Some fibres
obtained by using the internal crystallisation method.
The infiltration and
crystallization procedures are conducted in either commercially available
universal crystallizing machine CRYSTAL or a special machine, CHIR, built up for
the particular aim to fabricate ICM-fibres. CRYSTAL has the process zone with an
8 kHz-induction-heated-graphite-susceptor/molybdenum-crucible set-up. The zone
limits the length of the molybdenum carcass by about 100 mm. The CHIRўs
process zone with a radiant tungsten heater allows dealing with molybdenum
blocks up to about 250 mm. While dealing with 5 to 8 molybdenum blocks in one
process, 120 to 150 g of fibres can be produced in CRYSTAL machine. Productivity
rate of CHIR is about one order of the magnitudes higher. Because crystallizing
a batch of the fibres by using ICM is actually similar to making bulk crystals,
an expected cost of ICM fibres is of the same order of magnitudes as that of
bulk crystals.
References
[i].
H, E. LaBelle, Jr., A. I. Mlavsky,. Nature, 1967, 216, 574 - 575.
[ii]
J.-M. Yang, J. M. Collins, Proc. 4th Intern. Conf. Composites
Engineering (Ed.: D. Hui), ICCE, New Orleans, LO, 1997, p.1083.
[iii]
H. E. Bates, Ceramic Eng. Sci. Proc., 1992, 13, 190 – 197.
[iv]
D.-H. Yoon, T. Fukuda, J. Cryst. Growth, 1994, 144, 201 - 206.
[v]
S. T. Mileiko, V. I. Kazmin, J. Mater. Sci.,
1992, 27, 2165 - 2172.
[vi]
S. T. Mileiko, Metal and Ceramic Based Composites, Elsevier, Amsterdam,
1997.
[vii]
S. T. Mileiko, V. M. Kiiko, N. S. Sarkissyan, M. Yu. Starostin, S. I.
Gvozdeva, A. A. Kolchin, G. K. Strukova, Compos. Sci. and Technol, 1999, 59,
1763 - 1772.
[viii]
V. N. Kurlov,
V. M. Kiiko, A. A .Kolchin,
S. T. Mileiko, J. Cryst.
Growth, 1999, 204, 499 - 504.