Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.eso.org/observing/etc/doc/helphawki.html
Дата изменения: Unknown Дата индексирования: Sun Apr 10 20:07:53 2016 Кодировка: Поисковые слова: sn 1987a |
![]() |
|
---|---|
HAWK-I Exposure Time Calculator |
|
Note: These tools are only provided for the technical assessment of feasibility of the observations. Variations of the atmospheric conditions can strongly affect the required observation time. Calculated exposure times do not take into account instrument and telescope overheads. Users are advised to exert caution in the interpretation of the results and kindly requested to report any result which may appear inconsistent.
The HTML/Java based interface allows to set the simulation parameters and examine interactively the model generated graphs. The ETC programs allow easy comparison of the different options relevant to an observing program, including target information, instrument configuration, variable atmospheric conditions and observing parameters. Being maintained on the ESO Web servers, the ETCs are regularly updated to reflect the known performance of ESO instruments.
The exposure time calculator consists of two pages.
Input page: The observation parameters page presents the entry fields and
widgets for the target information, expected atmospheric conditions,
instrument configuration, observation parameters such as exposure time
or signal-to-noise, and results selection. An "Apply"
button submits the parameters to the model executed on the ESO Web server.
Output page:
The results page presents the computed results, including number of counts
for the object and the sky, signal-to-noise ratios, instrument efficiencies,
PSF size etc.. The optional graphs are displayed in several formats. Finally a summary of the input
parameters is appended to the result page.
Note: These tools are only provided for technical assessment of observation feasibility. Variations of the atmospheric conditions can strongly affect the required observation time. Calculated exposure time do not take into account instrument and telescope overheads. Users are advised to exert caution in the interpretation of the results and to report any result which may be suspected to be inconsistent.
The exposure time calculator models the observation chain which includes the target spectral distribution, atmosphere parameters, instrument configuration, and detector setup. An instrument description for HAWK-I is available on the instrument page.
The following options are available to describe the input spectrum of the target.
The flux density is constant at all wavelengths (F(λ) = const.) The flux density level is determined from the specified object magnitude.
The target model is a blackbody defined by its temperature, expressed in Kelvin. The intensity distribution is scaled to the object magnitude.
The target model can be defined by a template spectrum which is scaled to the provided magnitude and filter. The spectrum can be red-shifted.
References: Pickles (1998, PASP 110, 863); Coleman et al.: 1980ApJS; Kinney at al.: 1996ApJ.
Enter the V (650 nm), Y (1000 nm), J (1250 nm) , H (1650 nm), or K (2160 nm) magnitude, ideally
closest in wavelength to the selected filter.
The reference for the zero points used in conversion into photon fluxes:
Vega-system:
(B,V,R,I): Bessel, 1979, PASP, 91, 589. (J,H,K): Bessel and Brett, 1998, PASP, 100, 1134.
AB-system:Oke, 1974, ApJS.
The input spectrum is a single emission line. It is an analytic Gaussian, centered on the Wavelength parameter, defined by its total Flux and full-width at half-maximum FWHM. Line flux is given in 10-16 erg.cm-2.s-1.
NB: When requesting a single line as input spectrum, the magnitude parameter is not taken into account. Only the line flux will be used to determine the signal magnitude.
NB: The FWHM of a single line is limited by the sampling. If the requested FWHM is too narrow, it will be replaced by the minimum supported value, and a warning will be issued in the beginning of the result page.
Point Source are sources whose spatial extend on the sky is much less than the seeing diameter. The signal to noise is computed over a circular area with a diameter twice the Image Quality FWHM
.For extended sources, the magnitude is given per square arcsecond. The reference area for the signal-to-noise calculation can either be circular with the specified angular diameter, or it can be set to one detector pixel.
Since version 6.0.0, the definitions of seeing and image quality used in the ETC follow the ones given in Martinez, Kolb, Sarazin, Tokovinin
(2010, The Messenger 141, 5)
originally provided by Tokovinin (2002, PASP 114, 1156) but corrected by Kolb (ESO Technical Report #12):
Seeing is an inherent property of the atmospheric turbulence, which is independent of the telescope that is observing through the atmosphere; Image Quality (IQ), defined as the full width at half maximum (FWHM) of long-exposure stellar images, is a property of the images obtained in the focal plane of an instrument mounted on a telescope observing through the atmosphere. The IQ defines the S/N reference area for non-AO point sources in the ETC. With the seeing consistently defined as the atmospheric PSF FWHM outside the telescope at zenith at
500 nm, the ETC models the IQ PSF as a gaussian, considering the gauss-approximated transfer functions of the atmosphere, telescope and
instrument, with s=seeing, λ=wavelength, x=airmass and D=telescope diameter:
For fibre-fed instruments, the instrument transfer function is not applied. The diffraction limited PSF FWHM for the telescope with diameter D at observing wavelength λ is modeled as:
\(F_{\text{Kolb}} \) is the Kolb factor (ESO Technical Report #12):
|
The Paranal seeing statistics is based on the so-called UT seeing measurements obtained from the UT1 Cassegrain Shack-Hartmann wavefront sensor used for active optics.
The measurements are deconvolved in order to represent the seeing outside the dome (i.e. they are corrected for the instrument+telescope resolution).
The La Silla seeing statistics is based on the DIMM FWHM measurements corrected for the instrumental resolution.
These data come from http://www.eso.org/gen-fac/pubs/astclim/paranal/seeing/singcumul.html
The DIT (Detector on-chip integration time in seconds) is needed as input for both of the following cases:
Send comments and questions to usd-help@eso.org | ![]() |