|
Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.atnf.csiro.au/vlbi/wiki/index.php?n=Main.ParkesObservingSummary
Дата изменения: Unknown Дата индексирования: Tue Apr 12 18:05:54 2016 Кодировка: Поисковые слова: п п п п п п п п п п п п п п п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п |
|
Main /
ParkesObservingSummaryParkes ObservingOverviewParkes antenna control is via a command line program called atsnap. atsnap will run a simple schedule and can take commands to stow/unstow the antenna etc. IF setup is done seperately - normal observers would not normally worry about this. Attenuation is done via the "loGUI" software. The VLBI backend consists of two "LBA DAS" which sample and filter the IF and the LBADR recorder which captures the sampled data, formats it in software and writes to local or remote disk (or streams for eVLBI). The DAS setup is controlled via the "DAS GUI" and the recorder via "cdisko2". These are the same for ATCA, Parkes and Mopra and some documentation is available at: http://www.atnf.csiro.au/vlbi/wiki/index.php?n=Main.ObservingNotes All Antenna and VLBI control is from the joffrey:1 VNC. The joffrey :2 VNC is not used. Antenna controlThe antenna is controlled via a commandline program called atsnap, run on joffrey. All LBA schedules should be i the directory > cd ~/lba > atsnap vt999a.psn where v999a, in this example, is the name of the experiment. StowingTo stow the antenna, make sure atsnap is not running (^C if it is) and on a terminal on joffrey type: > atsnap stow Monitor in FROG that the antenna stows. UnstowingCheck first on FROG the antenna really is stowed. If so, on a terminal on joffrey type: > atsnap unstow Monitor on FROG that the antenna moves out of stow position. The takes a few minutes - do not attempt to move the antenna until the unstow is complete. Note that atsnap does not return error messages - you can only tell the unstow failed by looking at FROG. AttenuationAttenuation can be adjusted from "loGUI". If it is not running in one of the VNC windows you can start it from the "Observing Tools" menu at the bottom left of the VNC. ALWAYS remember to click "refresh" on loGUI (bottom left of window) to be sure the settings are up to date. Use the "C12att" attenuations and "C40att" do adjust attenuation. The C12 attenuators are in two pairs. Usually the left hand pair is connected to the VLBI backend and control each polarisation on both DAS/frequency chain. For some receivers the 3rd and 4th C12att are connected to the VLBI backend. The only way to know is ask (or be told). You can try changing the attenuation and see which has an affect but be sure to remember to set it back to the original value if it had no affect. The four C40 attenuations control the two polariation of each DAS separately. Usually the most left hand C40 controls DAS1 IFP#1 (pol A), the next DAS1 IFP#2 (pol B) etc. However it is not unusual for there to be a swap between the two polarisaions. When you change the values just note which DAS input is affected. You should preferably use the C12 attenuations to adjust levels but as these change the values for both DAS you may need to adjust the C40 to allow for DAS specific differences MonitoringYou should regularly monitor the following every 10-15 minutes
Troubleshooting
|