Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.atnf.csiro.au/vlbi/wiki/index.php?n=LBAAug2013.V255T
Дата изменения: Unknown Дата индексирования: Tue Apr 12 15:11:56 2016 Кодировка: Поисковые слова: п п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п р п п р п п р п п р п п р п п р р п р п п р п р п п р п р п п р п р п п р п |
V255Tv255t
Setup v255t.5cm-icrf:
Setup v255t.5cm:
Mode changes: Comments:At Cd Ho Mp Pa: Dual frequency setup required. Will need special DAS setup The purpose of these observations is to obtain the subsequent epoch for proper motion/parallax for G263.250+0.514, G305.202+0.208, G305.208+0.206 and G305.200+0.019, G339.884-1.259, G339.681-1.208 and G339.682-1.207. The G263.250 observations should show a modest peak at a sky frequency of 6667.8 MHz. The G305.21 observations should show a modest peak at a sky frequency around 6668.9 and the 339.88-1.26 should show a strong peak at a sky frequency of around 6668.9 MHz during these observations. During the ICRF runs we have sometimes had to exclude certain antennas (particularly Parkes and Hart) from observations of some sources in order to get a good spread of azimuths and elevations. Observing comments for each antenna: Hobart, Ceduna : The 4 x 16 MHz bandpass setup requires feeding two separate LOs into IFP#1 and #2 on the DAS/frequency translator. For Hobart the LOs should be set to 468 MHz (IFP#1) and 810 MHz (IFP#2) for the 4 x 16 MHz setup and 810 MHz for the 2 x 16 MHz setup. For Ceduna, if you set the agilent to 11.1 GHz rather than 11.4 GHz, then you can use the same LOs as at Hobart. The level into IF#1 will change significantly between the two setups. Set the level into the DAS so that it is within range for both setups. Setup the system temperature measurement so that it works for both IFs for the v255s.5cm setup. Please don't change the attenuation into the DAS when the setup changes as that may change the delay. Mopra :Note the use of the dual sideband vsop profile. Only the lower sideband should be selected for transfer. Note the use of the dual sideband vsop profile. Only the lower sideband should be selected for transfer. The basic method and frequencies for this experiment are the same as for v255s in June 2013 (and earlier: Mar 13, Mar 12, Nov 11). As for the earlier experiments for the ICRF observations it is 2 IFs with different polarizations. The times for the setup (mode) changes are given above. Not observing from 227/16:25 - 17:05. ATCA :For the ATCA please phase-up antennas CA01 through CA05 for this experiment. Setup as for a 2p-4IF experiment (dual DAS with huygens cable for entire experiment) with DAS1 tuned to the lower frequency and DAS2 to the upper frequency. Use the feature in cdisko version 4 to automate the changes of channel selection as per the following table. v255t.5cm Channels 5-8 v255t.5cm-icrf Channels 1,2,7,8 Not observing from 227/15:45 - 17:05. Parkes :Not observing during these times: 226 / 18:52 - 20:34 Hart:Observations at Hart begin at 227/01:15-01:30 UT for ICRF observations, and then delay calibration from 02:00-02:12 UT. Target observations begin at 227/04:04. Hart only participates in 2nd and 4th ICRF bloc observations. Not observing during these times: 226 / 18:00 - 227 / 01:15 Observing comments for each antenna:
Observing LogsParkes onsource flagging WeatherATCA Weather Monica log information - EXPERIMENTAL: |