Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://www.atnf.csiro.au/vlbi/dokuwiki/doku.php/difx/difx_monitor
Дата изменения: Unknown Дата индексирования: Sun Apr 10 21:25:23 2016 Кодировка: IBM-866 Поисковые слова: о п п |
DiFX has hooks to dump a copy of all accumulated visibilities down a TCP stream for online viewing, processing etc. Only single program can receive this stream. To allow multiple clients to simultaneously receive this monitoring data, a monitor_server can be run which receives a copy of ALL visibilities and allows multiple clients to connect. The clients request which of the visibilities they require and monitor_server only sends on the products required (so e.g. a client can be run over a moderately slow link if it only requires a handful of products).
Add the option -Mhost:port
to the mpifxcorr options, where host
is the host running monitor_server, and port is the TCP port to use. Note typically the host will be localhost
e.g.
mpirun -machinefile machines -np 10 /home/vlbi/difx/bin/mpifxcorr v999.input -Mlocalhost:9999
Either before or after mpifxcorr is started, monitor_server should be run. monitor_server would normally be run on the headnode running difx, but does not have to be (as long as mpifxcorr is told which host it is running on). monitor_server is designed to run persistently, ie it is not started and stopped each time a job is run. Note that two instances of monitor_server cannot be run on the same host, nor can monitor_server support two simultaneous instances of mpifxcorr. monitor server is simply run as monitor_server PORT
where port is the same port mpifxcorr was told.
e.g.
monitor_server 9999
Clients connect to monitor_server to display a subset of the visibilities. Note that most clients require a copy of the difx .input file. If they are run on a different host than difx (and without a shared filesystem). The .input file and some other setupfiles (e.g. .uvw) will need to be copied.
difx_config
Prints the product numbers (used by the following clients) and the associated
baseline, frequency, polarisation etc.
Usage:
difx_config <experiment.input>
e.g.
difx_config v999.input 0: CATW102-MOPRA RR 1405 MHz (16 MHz) 1: CATW102-MOPRA LL 1405 MHz (16 MHz) 2: CATW102-MOPRA RR 1421 MHz (16 MHz) 3: CATW102-MOPRA LL 1421 MHz (16 MHz)
mon_sample
was originally a coding example for using the monitoring infrastructure, but has proved to be a useful program in its own right. The name may change with no notice! mon_samples plots amplitude and phase vs frequency and amplitude vs delay (ie lag function) for up to 4 products.
Usage:
mon_sample <host> <inputfile> <product#> [<product#> ...]
where host is the host running monitor_server, inputfile is the difx input file currently being used and up to 4 product numbers can be specified.
e.g.
mon_sample localhost v999.input 0 8 16 24
difx_monitor
creates an html table and plots a .png plot for every visibility. Because the plotting is quite slow, it might be advisable to use a longer integration time if either the original integration time is short or a lot of products need to be plotted (e.g. large number of baselines). To be useful difx_monitor needs to be run on a host with a web server (and run in a directory visible to the web server).
Usage:
difx_monitor <inputfile> <host> [intergration]
where host is the host running monitor_server, inputfile is the difx input file currently being used. integration is an optional argument which gives a longer integration time (in seconds) to make plots for. The actual integration time sued will be the closest integral number of difx integrations to this number.
e.g.
difx_monitor v999.input cave00-ext 10
e.g.
mon_sample localhost v999.input 0 8 16 24
Vcal calculates the average delay of each station to a reference antenna then updates the input file to remove the offsets. DiFX needs to be restarted before these changes are seen. For each non-reference station, the delay offset for each baseline to the reference is computed then those above a SNR threshold averaged (unweighted). The algorithm for computing the delay is very simple and only good to 0.5 samples.
Usage:
vcal <inputfile> <host> [refant [# samples]]
where inputfile is the inputfile currently being used, host is the host running difx_monitor. refant
is an optional argument to change the referenced antenna from the default (the first in the input file). By default a simple integration is used - by setting the 4th argument more can be averaged together.
mon3d displays a 3D fringe plot of a single product (a 2D FFT of the visibilities, so showing the delay and rate). It is useful for public demos etc. It uses the S2plot 3D libraries.
Usage:
mon3d <product>
monitor_server and the clients are not built by default. Change directory to applications/difx_monitor (and trunk/branches etc if appropriate) and type make. You will need to install by hand. You can also try:
install-difx --withmonitor
which will attempt to compile and install monitor_server and clients.