Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.atnf.csiro.au/computing/software/miriad/userguide/node214.html
Дата изменения: Unknown
Дата индексирования: Mon Apr 11 02:22:08 2016
Кодировка:
Поисковые слова: р р р р р р п п р р

Bandpass and antenna gain calibration

When calibrating 3-mm data, it is possible to use a similar approach as with lower frequency data - see Chapter 11. In this case, because polarimetry is not currently possible with the 3-mm system, only task mfcal is needed to perform bandpass and antenna calibration. Flux density bootstrapping can be accomplished using mfboot described below.

However, the recommended approach at 3mm is different from this. As noted in Section 23.1.4, calibration at 3mm is more difficult because of weak calibrators, poorer system sensitivity and more challenging atmospheric conditions. This section outlines an alternative calibration approach exploiting the dual frequency bands of the ATCA. The steps are as follows:

1. The first step is not a step at all! Unlike the approach of Chapter 11, the approach described here does not split the data into separate single source, single frequency files before calibration. Rather the current approach assumes that you have a single Miriad dataset containing bandpass calibrator, secondary calibrator, flux density calibrator and target source. We focus on data having two simultaneous frequency bands here, but the approach works equally well for one or many simultaneous frequency bands within the dataset.

2. The first real step is akin to a bandpass calibration step. When dealing with two frequency bands, each with two polarisation products (XX and YY), it is generally appropriate to assume that the bandpasses of the bands and the phase offsets between bands and polarisations are constant with time.

   To determine the bandpasses and the phase offsets, you need to use mfcal on an observation of a strong continuum source. Typically this would be 1253-055, 1921-293 or 0537-441. Typical inputs are as follows:

   MFCAL
   in=vela.fixed.uv	Input multi-source, dual-band dataset.
   select=source(1921-293)	Select the strong continuum ``bandpass'' calibrator.

   The important output of this step is a bandpass calibration table which will contain the relevant phase offsets. The output also contains antenna gain calibration tables, but this will be overwritten below.

   In doing this step, you may well want to avoid using some edge channels in the bandpass calibration process. To achieve this, you can use the edge parameter of mfcal. The edge parameter sets the number of channels to drop for all bands equally. It does not allow you to set different number of channels to drop in the different bands. If the channels and bandwidth characteristics of the different bands differ significantly, the edge parameter probably does not give you sufficient flexibility. In this case, you could use uvflag to explicitly flag edge channels.

3. The next step is to determine the antenna gain calibration, again using mfcal. To do this, you will want to select those data for the secondary calibrator which will give the best overall sensitivity appropriate to your observation.
   • If the calibrator is a continuum source, you need only select this source and use both bands. Task mfcal will weight the two bands according to their relative bandwidth. Consequently if one of the bands is quite narrow relative to the other, then it will contribute little to the overall gain solution.
   • If the calibrator is an SiO maser, you will want to select only those channels that contain strong SiO signal.
   • With either a continuum calibrator or an SiO maser, it is possible to either determine antenna gain calibrations for the two polarisation products independently, or to determine a single joint solution for the two polarisations. The latter will give a $\sqrt{2}$ improvement in sensitivity in the solution process. The latter is also the desirable approach if the calibrator is strongly polarised (some SiO masers are more than 50% polarised). Doing a joint solution is generally a reasonable approximation given that the antenna gains are dominated by changes common to both polarisations: in amplitude, it is from the physical antenna gain change, and in phase it is from the atmosphere and instrumental contributions common to both polarisations.

   Note in this calibration scheme, it is implicitly assumed that the antenna gain changes are common to both frequency bands. This is a reasonable approximation given that the frequency separation between the bands is at most 2.7 GHz and potentially much less. Consequently the fractional frequency separation in at most a few percent, and so the calibration change between bands can be assumed to be minimal.

Typical inputs for mfcal follow. This assumes a continuum source as the secondary calibrator and does a joiubt solution for the two polarisations:

MFCAL
vis=vela.fixed.uv	Input multi-source, dual-band dataset.
select=source(1622-297)	Select secondary calibrator.
options=nopassol	Do not solve for bandpass.
stokes=i	Do a joint solution for both polarisations.

To derive a separate solution for the two polarisation products, the stokes keyword would be left unset. Note the use of options=nopassol. This causes mfcal to not attempt to solve for the bandpass and phase offsets again, but rather to apply the previously determined bandpass and phase offset solutions.

Typical inputs when using an SiO maser would be as follows: Typical inputs to mfcal are as follows:

MFCAL
vis=vela.fixed.uv	Input multi-source, dual-band dataset.
select=source(oceti)	Select SiO secondary calibrator.
options=nopassol	Do not solve for bandpass.
stokes=i	Do a joint solution for both polarisations.
line=chan,20,45	Select the range of channels where the SiO
	signal is strong.