Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.arcetri.astro.it/irlab/fasti/l3ccd/2014_3.pdf Дата изменения: Thu Jul 28 18:23:55 2005 Дата индексирования: Sat Dec 22 06:48:25 2007 Кодировка:

Marconi Applied Technologies

IMAGING

PROVISIONAL
CCD65

> > > > > >

576(H) X 288(V) PIXEL IMAGE AREA

525 or 625 LINE FORMAT (INTERLACED) INVERTED MODE OPERATION (MPP) 20 X 30 µm PIXELS

NOVEL PREAMPLIFIER FOR EXTREMELY LOW NOISE AT HIGH PIXEL RATES 100% ACTIVE AREA

The next revolution in imaging is here

TM


Marconi Applied Technologies

IMAGING

The CCD65 uses a completely novel output amplifier circuit that is capable of operating at an equivalent output noise of less than one electron at pixel rates of over 10MHz (corresponding to a field rate of 50Hz). This makes the sensor well suited for scientific imaging

where the illumination is limited or for video applications at very low light levels. The sensor operates in the inverted mode to suppress dark current as this is now the dominant noise source (even at 50Hz field rate). Antiblooming

is optional. The output amplifier may be switched from the very high gain mode to normal operation by control of one of the operating voltages (details should be discussed with Marconi Applied Technologies).

Format Image Area Active Pixels Pixel Size (mm) (H) (V) (µm) 11.52 x 8.64 576 288 20 x 30

Additional pixels are provided for overscanning purposes. Number of Output Amplifiers 1 The device has a 100% fill factor for maximum sensitivity.

Note 1 The gain may be adjusted by changing the relevant drive voltage Dark Signal (at 293K) (e-/pixel/s) 200 Charge Transfer Efficiency (%) Parallel 99.9999 Serial 99.9993 Dark Sig Non-Uniformity (at 293K, e-/pixel/s) 80 Minimum Spectral Range (nm) 400 - 1060

Ref. VDOS VABD VABG VDC VHG

Description Dummy Output Source Antiblooming Drain Antiblooming Gate Phase High Gain Adjustment See Note 2 15V 0V 5V See Note 3

Note: All values quoted using typical operating conditions at a frame rate of 50Hz and at a temperature of 293K (approx).

Note 2 An external load is required which may either be a constant current source of approximately 7.5mA or a 3.3k resistor Note 3 Contact Marconi Applied Technologies for details of the operation of the increased gain feature

Package Ceramic Package non peltier pack 36-pin PGA

Typical Operating Conditions Ref. VSS | I01 | I02 | S01 | S02 | R01 | R02 | R03 | 0R VOG VRD VOD VOS VDOD Description Substrate Image Clocks (high level) (low level) Store Clocks (high level) (low level) Register Clocks (high level) (low level) Reset Pulse (high level) Output Gate Reset Drain Output Drain Output Source Dummy Output Drain 5V 11V -5V 11V -5V 12V 0V 12V 3V 18V 28V See Note 2 28V

Blemish Specification Grade Column Defects-black or slipped -white Black Spots Traps > 200eWhite Spots

0 0 0 10 1 10

1 1 0 15 2 15

2 6 0 30 6 50

Typical Performance In Normal Mode O/P Amp Responsivity Peak Signal Peak Output Voltage Readout Noise at 50Hz In High Gain Mode O/P Amp Responsivity Peak Output Voltage Readout Noise at 50Hz (µV/e-) Note 1 Up to 500 (V) 1.0 (e- rms) <1 (µV/e-) (e-/pixel) (V) (e- rms) 1.3 200,000 0.84 <100

Waterhouse Lane Chelmsford Essex CM1 2QU United Kingdom T +44 (0) 1245 493493 F +44 (0) 1245 492492 E-mail MTech.uk@marconi.com

16 Burospace 91572 Bievres Cedex France

4 Westchester Plaza Elmsford NY 10523-1482 United States of America T (914) 592 6050 F (914) 592 5148 Toll free 1-800 342 5338 E-mail MTech.usa@marconi.com
January 2001 issue 3

TM

T (331) 6019 5500 F (331) 6019 5529 E-mail info.marconitech@gec-france.fr