Äîêóìåíò âçÿò èç êýøà ïîèñêîâîé ìàøèíû. Àäðåñ
îðèãèíàëüíîãî äîêóìåíòà
: http://www.astro.louisville.edu/software/xmtel/archive/xmtel-3.1/docs/nexstar/NexStar_Info.html
Äàòà èçìåíåíèÿ: Fri Apr 11 00:27:48 2003 Äàòà èíäåêñèðîâàíèÿ: Mon Oct 1 22:58:18 2012 Êîäèðîâêà: Ïîèñêîâûå ñëîâà: ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï ï |
Here is some info I've compiled on the NexStar GPS Telescope operation.
Disclaimer: Use this information at your own risk! It
is my opinion only.
Feel free to mail me at: andre@paquettefamily.ca
for any comments, corrections, or suggestions.
NexStar AUX Command Set
Hand Controller
Motor Controller
GPS Module
Serial Problem with HC
Autoguiding with Joy(stick)
PC Control Cables
The NexStar GPS hand controller employs a PIC17C756A processor.
The HC firmware can be found in two socketed chips. These chips are Atmel AT49F040 512K flash devices .
With the HC display on the top, the leftmost flash device is the "even"
part -- the chips have 2 dots on the top.
The rightmost device is the "odd" part and has 1 dot on the top.
Firmware can be extracted from the flash devices and units upgraded
via a programmer.
Note that the sockets are quite fragile and it takes a fair bit of
force to remove the chip, so be sure to use proper chip removers if you
intend to play -- and be careful.
Finally, here is the manual
for HC 1.6 features.
Debug mode:
There is a hidden mode in the hand controller that gives you access to some
low-level information. To enter this mode, hit 6, then 7 from the "NexStar
GPS" level.
Here's what this mode gives you:
Action/Version |
1.6 |
2.2 |
Mode entered |
"up time" displayed |
blank screen |
1 Button |
N/A |
read/write seep |
3 Button |
read/write seep |
read/write seep |
7 Button |
get compass heading |
get compass heading |
8 Button |
get detailed GPS info |
N/A |
0 Button |
displays HC version, allows retrieval
of version from other devices |
N/A |
For the detailed GPS info, the displayed format is:
"A B H:M:S"
"CD E F G"
Where:
A is the number of tracked satellites,
B is the MSB of the RCVR Status
H:M:S is the time in GMT
C is the month
D is the day
E, F, and G are the raw values for the latitude.
Not all PC serial ports are made equal. When not in use, most serial
ports idle with a stop bit. However, some serial ports send a continuous
start bit (break signal) when not in use. If the HC serial port receives
a continuous start bit, it gets confused or bogged down and has difficulties
sending characters the next time you connect. For instance, if you
try connecting to the HC with "TheSky" you'll get errors 9/10 times.
Often, BIOS upgrades are available that will change the serial port
behaviour and work around the problem. Also, you could get a serial-to-USB
device and hope that it idles with stop bits.
Either way, this is a bug with the serial handling on the HC and hopefully
Celestron will correct it on the next spin.
It it is really easy to make a cable that allows the autoguider port to interface with the old-style Commodore/Atari joysticks. These old joysticks will fit into a male DB9 connector and are great for doing manual guiding. Wico command/control meets NexStar GPS...
AG pin 1 -> N/C
AG pin 2 -> DB9 pin 8 (GND)
AG pin 3 -> DB9 pin 4 (+RA)
AG pin 4 -> DB9 pin 1 (+DEC)
AG pin 5 -> DB9 pin 2 (-DEC)
AG pin 6 -> DB9 pin 3 (-RA)
Cables for sale
Parts used
9-pin serial pinout
HC serial pinout
PC port pinout
I'm selling cables (at just over cost) for interfacing your computer to
the NexStar telescopes.
There are two kinds of cables: one to connect to the hand controller,
and one to connect to the PC port. The table below lists the prices.
Shipping is extra.
Part |
Canadian $ |
US $ |
Complete HC Serial Cable |
$7.78 + $0.12/foot |
$5.12 + $0.08/foot |
Complete PC Port Cable |
$7.98 + $0.18/foot |
$5.24 + $0.12/foot |
DB9F to RJ45 Adapter Only |
$6.87 |
$4.52 |
HC Serial Cable Only (no DB9 end) |
$0.91 + $0.12/foot |
$0.60 + $0.08/foot |
PC Port Cable Only (no DB9 end) |
$1.11 + $0.18/foot |
$0.73 + $0.12/foot |
Cables are made from 4 or 6 conductor flat cable with an RJ45 connector at one end and either an RJ45 or RJ11 handset plug at the other end. The RJ45 connector plugs into an adapter that converts the RJ45 to a 9-pin female end for use with a computer.
If you wanted both a PC port and a HC serial cable but weren't going to use both at the same time, you could buy one "DB9F to RJ45 Adapter" and then the "Cable Only" parts for each type of cable.
If you're interested in purchasing a cable, send me an email with the
type, length and number of cables you would like and the address to use for
shipping. I'll then send you an email when the cable is ready and the
expected cost including shipping. You can then send me a cheque and
I'll send you the goods.
Here are the parts used to make the cables:
DB9F
to RJ45 modular connector
RJ45
plug
RJ11
handset plug
"Silver
Satin" 6-conductor cable
"Silver
Satin" 4-conductor cable
Here is the pinout for the DB9F connector:
Pin 2 -> data to computer from telescope
Pin 3 -> data from computer to telescope
Pin 5 -> ground
Pin 7 -> RTS
Pin 8 -> CTS
Here is the pinout for the HC Serial
interface:
Pin 1 -> data to computer from telescope
Pin 2 -> ground
Pin 4 -> data from computer to telescope
Additional information on how to make a
HC serial cable can be found on Mike Swanson's site.
Important: Pin1 is the pin on the lower right side of the diagram
on Mike's page.
Here is the pinout for the PC Port
interface:
Pin 1 -> ground
Pin 2 -> data from computer to telescope
Pin 3 -> ground
Pin 4 -> data to computer from telescope
Pin 5 -> RTS
Pin 6 -> ground
Pin 7 -> CTS
Pin 8 -> ground
Additional information on how to
make a PC port cable can be found on Mike Swanson's site.
Important: Pin1 is the pin on the lower right side of the diagram
on Mike's page.