Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.adass.org/adass/proceedings/adass94/aket.html
Дата изменения: Sat Nov 4 01:46:25 2000
Дата индексирования: Tue Oct 2 00:43:30 2012
Кодировка:

Поисковые слова: вфптбс лпунйюеулбс улптпуфш
Calculating the Position and Velocity Components of HST



next up previous gif 168 kB PostScript reprint
Next: Robust Data Analysis Up: Data Modeling and Previous: Interpolation of Irregularly

Astronomical Data Analysis Software and Systems IV
ASP Conference Series, Vol. 77, 1995
Book Editors: R. A. Shaw, H. E. Payne, and J. J. E. Hayes
Electronic Editor: H. E. Payne

Calculating the Position and Velocity Components of HST

T. B. Ake
Astronomy Programs, Computer Sciences Corporation, Code 681/CSC, Goddard Space Flight Center, Greenbelt, MD 20771

 

Abstract:

The HST uses an onboard model of its orbit to perform in real-time various control functions relating to spacecraft operations and observation support. The flight software uses the equation of center to solve Kepler's equation for two bodies. New coefficients for the ephemeris are updated every other day, and are archived as FITS keywords for each HST observation data set. Using these coefficients,an observer can perform a variety of calibration and characterization calculations relating to the orbital position and velocity of the telescope. We present here the methodology for computing the HST state vectors using this information.

       

Introduction

Many precise measurements with the Hubble Space Telescope ( HST) require knowledge of its position and velocity during the observations. Orbital parallax, velocity aberration, Doppler shift, and light-travel time can all be significant when converting HST observations to the geocentric system, and from there to the barycenter of the solar system. In addition, the quality of observations are affected by the near-earth environment in which HST operates. An observer would be wise to understand such effects as scattered earth light, radiation background, and geomagnetically-induced motion on the data.

One way to determine the motion of HST during an observation is through the definitive orbit files that are archived at the Space Telescope Science Institute (ST ScI). Every other day the Flight Dynamics Facility (FDF) at Goddard Space Flight Center computes the position and velocity of the HST for the previous two days based on ranging measurements of the spacecraft. This information is forwarded to the ST ScI in the form of a list of HST state vectors for each minute of time, with each record giving the J2000 rectangular components of the position, in km, and velocity, in kms, in the geocentric inertial coordinate system. The observer must find and extract the appropriate file(s) from the archive and interpolate the HST state vector data to the relevant times of the observations.

An easier method is to use the onboard ephemeris parameters that are provided with the data sets themselves. When the definitive orbit file is generated by the FDF, a set of ephemeris coefficients is created. The HST flight software uses these coefficients for various spacecraft control functions. During pipeline processing at the ST ScI, these are archived in the *.shh (non-astrometry) or *.dbm (astrometry) header file for each observation. We summarize using this information to compute the position and velocity of the HST.

 
Table: Onboard Ephemeris Model Parameters

Computations

The HST travels in a nearly circular orbit, with an altitude of about 600km and velocity of 7.5kms. The orbital model used onboard is based on a simple two-body system, with perturbations to certain Keplerian elements due to the proximity of the earth. In Table 1 we list the relevant FITS keywords and descriptions that can be found in the header files, as well as the symbols used in the equations below.

The steps to compute the geocentric, rectangular coordinates for the HST using the parameters in Table 1 are as follows. First, the observer should verify that the correct onboard ephemeris has been archived with the data. The TIMEFFEC keyword specifies the beginning time at which the parameters are valid and its value should be within 2--3 days before the start of the observations.

For a time of interest, t, calculate the mean anomaly, M, from the initial position, M, at the epoch time of the parameters, ,

Compute the true anomaly, , using the equation of center to solve Kepler's equation. This is typically expressed as a series in and e. For small e, terms only up to are needed (e.g., Smart 1965, equation V-85),

Since trigonometric functions are computationally expensive, HST uses a different form of this equation involving only and . Collecting like terms of and expanding , one can show

Once the true anomaly is known, then the distance from the center of the earth, r, is

The main perturbation on the orbital elements due to the non-spherical mass distribution of the earth is the regression of the ascending node, , and the progression of perigee, , (Wertz 1978). The instantaneous values at t are

The geocentric HST position, in J2000 rectangular coordinates in meters, is then

The corresponding equations for radial velocity can be derived by differentiating those for position. Starting with x,

To eliminate the and terms, we use a well-known property of elliptical orbits that the velocity can be represented as the vector sum of two constant velocities (Smart 1965). These are the velocity, , perpendicular to the radius vector and, , perpendicular to the semimajor axis, where and . Designating V as the circular velocity, we have

The rectangular velocities can now be determined from the onboard ephemeris parameters. Defining the auxiliary variables

we have

Equations (1)--(7) yield the geocentric state vectors for HST.

 
Figure: Typical positional errors from an on-board ephemeris. Original PostScript figure (82 kB)


Comparisons with Definitive Orbit Data

We can compare the results from the ephemeris model directly with the definitive orbit data. In Figure 1 we show the total error in position for several days during the first week of 1994 April. In this example the error is below 2km for the two days during which the ephemeris is active. After this time, the error slowly increases, reaching about 5km a week outside the two-day range of the model. The error in velocity was found to be only 0.01kms over the whole period investigated. Comparisons for other weeks indicates that the positional error can be as high as 4km, but the velocity error is always very small, since the orbit is nearly circular.

Conclusions

Results using the onboard ephemeris are accurate enough for most needs. A positional error of 4km translates to an uncertainty of 1mas at 5.5AU from the earth, so parallax errors are small for all but nearby passing asteroids and comets. The geographic position of HST can be determined to better than , much more accurately than needed to compute effects due to the orbital environment. The error in velocity is much smaller than can be measured with the HST instruments. We conclude that using the onboard ephemeris eliminates the need to import definitive orbit data. This exemplifies the value of providing users with self-documenting data sets so that further analyses can be performed without resorting to additional outside information.

References:

Smart, W. M. 1965, Spherical Astronomy (Cambridge, Cambridge University Press)

Wertz, J. R. 1978, in Spacecraft Attitude Determination and Control (Dordrecht, Reidel), p. 65



next up previous gif 168 kB PostScript reprint
Next: Robust Data Analysis Up: Data Modeling and Previous: Interpolation of Irregularly

adass4_editors@stsci.edu