Документ взят из кэша поисковой машины. Адрес
оригинального документа
: http://hea-www.harvard.edu/PROS/PUG/node202.html
Дата изменения: Unknown Дата индексирования: Mon Oct 1 23:31:15 2012 Кодировка: Поисковые слова: п п п п п п п п |
The following script will create an individual qpoe file (64x64
pixels) for each obi, with the filename containing the obi number.
The obi times are read from the ASCII file 'obi_times.asc' (created
in section 13.2.4). This script will then produce smoothed
image files and send a contour plot to either the screen or the printer.
Run obidiv.cl to plot out the contour maps of each individual obi:
>xspatial
>xplot
>task obidiv=obidiv.cl
Here is a sample of the parameter settings:
qpfile = "rh70088100.qp" Original Qpoe file
obi_list = "obi_times.asc" File containing the obi times
out_files = "3C120" Root name for output files: root??.qp
xpos = 4101 X source coordinate
ypos = 4068 Y source coordinate
gauss_sm = 2.54 Gaussian smooth sigma in pixels
cntr_lv = "5 25 50 75 95" Contour levels (percent of peak)
(flist = )
(mode = "ql")
NOTES:
-------
-For printouts set this imcontour parameter ('epar imcont'):
graph_device = "stdplot"
-For a continuous dump of the contour plots to the screen, set:
graph_device=stdgraph
gclose=yes
>obidiv
Method for Visual Inspection
On rare occasions, it may be useful to examine each phase bin visually
to evaluate the segments in order to decide if some should be deleted
before restacking for the final result. We have found it useful to do
this via contour diagrams of the source. This approach can be labor
intensive if there are a large number of obis and phase bins.
However, if you find that individual obis are reasonably well aligned
and you opt for stable roll angle intervals (each containing many
obis), then this method can be useful for weaker sources.
This visual inspection method involves running the script described
below to obtain contour plots of each phase bin; measuring centroids
by eye on the contour diagram and evaluating the PRF of each segment
in order to decide if some should be rejected; shifting each phase bin
with 'qpshift', and finally restacking the segments with
'qpappend_ftsi'.
This task is similar to 'phase_repos.cl' but without the source
detection algorithm that determines the source position. The input
file is the qpoe produced by 'qpphase'. The script will create an
individual qpoe file for each phase bin interval. The qpoe file will
be named by obi and phase number. As described for the task 'obidiv',
an output image will be sent to the screen or printer for each file
created.
>task phase_eval=phase_eval.cl
>xplot
>xspatial
With the parameters set as follows:
qpfile = "rh70088100_ph.qp" Qpoe file output by qpphase
obi_list = "obi_times.asc" File name containing the obi times
out_files = "3C120" Root name for output files: root_obi??_ph??.qp
num_phase = 10 Number of phase bins
xpos = 4101 X source coordinate
ypos = 4068 Y source coordinate
gauss_sm = 2.54 Gaussian smooth sigma in pixels
cntr_lv = "5 25 50 75 95" Contour levels
(flist = "")
(mode = "ql")
*** For selecting hardcopy or screen plots, see 'Obi Analysis'
in this same section.***
>phase_eval