Документ взят из кэша поисковой машины. Адрес оригинального документа : http://crydee.sai.msu.ru/ftproot/pub/comp/os/os2/xfree86os2/3.3.6/README.OS2 Дата изменения: Sun Jan 9 00:00:00 2000 Дата индексирования: Tue Apr 12 21:19:05 2016 Кодировка: Поисковые слова: movie

README for XFree86 on OS/2

Holger Veit

Last modified on: December 12th, 1999

1. Introductory Note about the release 3.3.6

Before looking into this file, please check for any LATEST.OS2 files that may
come with the binary distribution. Please also check out the following
XFree86/OS2 WWW pages:

o http://ais.gmd.de/~veit/os2/xf86os2.html

o http://ais.gmd.de/~veit/os2/xf86bugs.html

o http://ais.gmd.de/~veit/os2/x11os2faq.html

before you claim to have found any problems.

This version of the code is called XFree86/OS2 3.3.6. This is a bugfix
release for 3.3.5 and previous versions which again adds hardware support for
some newer cards, including AGP boards. XFree86-3.3.6 contains all security
fixes that were released for earlier versions. See the RELNOTES document for
details.

XFree86/OS2-3.3.6 is a full, unrestricted version which does not expire, and
for which the complete source code is available. In contrast to beta ver-
sions, we consider this code as sufficiently stable for use by an end user.
Since there have been numerous bugfixes, we recommend this version, even if
you had XFree86/OS2 3.3.x before and it worked satisfyingly with your hard-
ware. By the time 3.3.6 is released, the older version 3.3 will be withdrawn,
and archives will be updated to this version. There may still be references
to 3.3 or 3.3.x still in documents; these apply to 3.3.6 as well, unless oth-
erwise noted.

Previous versions have been tested in a large number of configurations and
have been found to be working, with some bugs left, rather flawlessly.

This release is almost complete (with a few exceptions) regarding the X11R6.3
``core'' distribution. A subset of the ``contrib'' distribution is available
from the ported software page http://ais.gmd.de/~veit/os2/xf86ported.html

In the past beta testing, it has been found that the software itself is
rather stable and does not damage hardware - provided the user does not try
to push the builtin limits and change certain configuration parameters which
could operate the video hardware out of specs.

However,

o even with a code we consider stable there is no explicit or implicit
warranty that certain code works correctly or works at all

o although no damage reports are known, it does not mean that it is impos-
sible to damage hardware with this code; some deeply hidden bugs may
still be present in the software.

It is recommended that you backup essential data of your system before
installing this software, but this should be your general precautions before
ANY installation. No reports exist that a crashing X server itself actively
destroys or modifies data, but it is possible in rare cases that the system
is left in an unusable state (video display mode garbled or system unrespon-
sive, not reacting to mouse or keyboard actions). If you then hard reset or
switch off the system, file caches of the operating system might not be writ-
ten correctly back to disk, thus causing data loss.

2. What and Where is XFree86?

XFree86 is a port of X11R6.3 that supports several versions of Intel-based
Unix. It is derived from X386 1.2, which was the X server distributed with
X11R5. This release consists of many new features and performance improve-
ments as well as many bug fixes. The release is available as source patches
against the X Consortium X11R6 code, as well as binary distributions for many
architectures.

XFree86/OS2 is the name of the implementation of XFree86 on OS/2 based sys-
tems.

See the Copyright Notice.

Binaries for OS/2 Warp, Merlin, and Aurora are available from:
ftp.XFree86.org:/pub/XFree86/3.3.6/OS2

The WWW page http://borneo.gmd.de/~veit/os2/xf86os2.html will usually show
more references to FTP or WWW sites to retrieve sources or binaries.

Other versions:

XFree86/OS2 will run on all dialects of Warp 3, including Warp "red spine
box", Warp "blue spine box", Warp Connect, Warp Server, and Warp 4.

For Warp 3 installing fixpack level 17 or later is strongly recommended.
There have been a few reports that the installation of FP26 causes XFree86 no
longer to work, but I am not sure about a real reason. Current fixpacks for
Warp 3, like FP36, seem to work well also.

Warp 4 may be used with or without the recent public fixpack.

Please check in all cases a LATEST.OS2 file.

OS/2 2.11 is not supported any longer with this release, due to lack of a
working test environment. Consequently, OS/2 SMP 2.11 is not supported
either. Warp Server SMP is supported, but SMP does not give significant
advantage, other than the general speedup because of multiple processors
working. OS/2 versions 1.X are definitely not supported and will never be.

It is possible to build XFree86/OS2 from the sources. Read about this in the
document OS2.NOTES.

3. Bug Reports for This Document

Send email to Holger.Veit@gmd.de (Holger Veit) or XFree86@XFree86.org if you
have comments or suggestions about this file and we'll revise it.

4. Hardware and Software Requirements

4.1 Supported, Required, and Recommended Hardware

o At least a 486DX33 with 16MB RAM is required. A Pentium or Pentium Pro
and more main memory is recommended. A 386 or a system with 8MB or less
memory is an insufficient configuration.

o There are no specific requirements concerning network cards, disk types,
or CD ROM equipment; of course the more powerful, the better.

o Depending on the packages installed, a disk space of 20-55MB on a HPFS
formatted partition (or a JFS, NFS or ext2fs partition natively allowing
long filenames) is required. XFree86/OS2 will not run on FAT partitions.

o You need a video card that is supported by XFree86. Refer to the general
README document for a list of supported cards. Note that the sets of
video cards supported by XFree86 on one hand and OS/2 on the other hand
overlap, but do not match exactly, i.e. the fact that your card is sup-
ported by OS/2 does not mean it works with XFree86 as well, and vice
versa. XFree86 does not use the video services of the OS/2 operating
system.

4.2 Required Software

o Any version of Warp 3 with at least fixpack 17, or Warp 4 is required

o XFree86/OS2-3.3.6 may use a local named-pipe connection or a TCP/IP
based network connection.

1. Warp comes with the Internet Access Kit (IAK), which is suffi-
cient. Warp Connect and Warp Server come with a full version of
TCP/IP (3.0). Use of this software is preferred over IAK then.

2. Warp 4 comes with TCP/IP 4.0 which should also work.

3. There are reports that with EMX 0.9 fix 4, you can also use the
new 32 bit IBM TCP/IP 4.1 product.

4. The old IBM TCP/IP 2.0, that comes with the IBM PMX product may be
used with Warp as well, although it is no longer supported by IBM.
Please ensure that you have the latest CSDs installed.

Other versions of TCP/IP, such as FTP's, DEC's, or Hummingbird's TCP/IP
versions, as well as IBM TCP/IP 1.X are not supported. Nor does any net-
working support from DOS (packet drivers, winsock), Netware, or NetBIOS
work, and I won't to provide support for that in the future.

o If you want to write or port applications for XFree86, you are encour-
aged to do so. You will need a complete installation of EMX/gcc 0.9C
fix4 or later for doing so. Neither the second (obsolete) implementation
of gcc, nor any commercial package, including Cset/2, VAC++, Borland
C++/OS2, Watcom C++, Metaware C, and others, is suitable for porting,
because various parts of the X DLLs rely on certain features only pre-
sent with EMX.

5. Installing the System

The binary distribution is composed of a number of zip archives which are the
executables, servers, fonts, libraries, include files, man pages, and config
files. The full distribution requires about 40-55MB of disk space.

All archives of this alpha version are packed with the info-zip utility,
which is available under the name UNZ512X2.EXE (or a later version) from many
OS/2 archives. Please obtain a native OS/2 version of this unpacker. DOS
PKUNZIP does not work, because it cannot unpack long file names and extended
attributes.

At this moment, the distribution covers only the ``core'' distribution which
somewhat reduces the usability. Refer to WWW sites and archives listed in the
XFree86/OS2 FAQ and elsewhere to obtain pre-built X clients which were ported
to XFree86.

The contents of the packages are:

REQUIRED:

Xbase
A special device driver and the SuperProbe program
Note: In order to fix a problem occurring with WSeB
(Aurora), you must install the most recent version of
the xf86sup.sys driver that comes with this file.
Older versions won't work.

Xdoc
READMEs and XFree86 specific man pages.

Xbin
all of the executable X client applications and
shared libs

Xfnts
the misc and 75dpi fonts

emxrt
Runtime libraries of EMX

Choose at least one of the following to match your hardware:

X8514
the X server for IBM 8514/A and compatible boards

XAGX
the X server for AGX boards

XGlnt
the X server for Permedia / GLINT boards

XI128
the X server for #9 Imagination 128 boards

XMa32
the X server for ATI Mach32 graphics boards

XMa64
the X server for ATI Mach64 graphics boards

XMa8
the X server for ATI Mach8 graphics boards

XMono
the Monochrome X Server

XP9K
the X server for P9000 based boards

XS3
the X server for S3 based boards (excluding S3 ViRGE)

XS3V
the X server for S3 ViRGE based boards

XSVGA
the 8-bit pseudo-color X server for Super VGA cards

XVG16
the 4-bit pseudo-color X server for VGA & SVGA cards.

XW32
the X server for et4000w32 based boards

OPTIONAL:

Xman
pre-formatted man pages for the X11 interface and
clients

Xf100
100dpi fonts

Xfscl
Speedo and Type1 fonts

Xfnon
Japanese, Chinese and other fonts

Xfcyr
Cyrillic fonts

Xfsrv
the font server with man pages.

Xprog
the X11 header files and programmer's utilities for
compiling other X applications

Xpex
PEX fonts and libraries required for PEX applications

In order to save space on your disk and reduce net bandwidth, choose the
software to obtain carefully. Each X server is an archive of about 1.2MB and
occupies 3.0MB on the disk. You won't normally need more than the single
Xserver tailored to your video card.

If it is your first time install, get the Xbase archive before any of the
other packages. This package contains a driver and a test program, which ana-
lyzes your video hardware. If this program fails or reports an incompatible
hardware, it makes no sense to obtain the other packages in the hope that
they would magically work.

6. Troubleshooting

Surprised to see this section directly in the beginning? We have put it here
because chances are best here not to overlook it. This does not mean that you
will necessarily encounter trouble when installing XFree86, but be warned:
the following sections are IMPORTANT and neglecting one or more things out of
impatience or sloppiness will leave you with a non-working X11 system and us
with unnecessary problems.

Still, due to the incredibly large number of hardware configurations, there
may be some special situations and configurations where the below description
is not successful. If this happens, read - I repeat READ - the list of ``fre-
quently asked questions'' (FAQ) which has meanwhile evolved to a trou-
bleshooting guide. The latest version is always at
http://ais.gmd.de/~veit/os2/x11os2faq.html .

Maybe - but we found you must be very creative - you find a bug. Consult the
page http://ais.gmd.de/~veit/os2/xf86bugs.html whether it is already known.
If not, you have a case and should report it to XFree86
(xfree86@xfree86.org). Please refer to the FAQ about the information to be
provided for a complete problem report.

The recommended newsgroup for setup questions is comp.os.os2.setup.misc. I
read this group, so it won't speed up the process or enforce anything if you
post to other groups, or forward the report to my mail address as well or to
xfree86@xfree86.org.

So, not to discourage you completely, the setup section begins:

7. Checking Compatibility of Video Hardware

In the following, we assume that you want to install XFree86/OS2 on a disk
drive with the letter Y: (which you probably don't have). Change the letter
in all commands accordingly.

1. Obtain the package Xbase and install it from the root directory of the
Y: drive, by entering the following commands:

[C:\] Y:
[Y:\] cd \
[Y:\] unzip \path_of_package\Xbase.zip

2. Edit your CONFIG.SYS file to contain the following line somewhere:

DEVICE=Y:\XFree86\lib\xf86sup.sys

Of course replace ``Y:'' with the correct drive letter.

3. At this point, you may consider to add the variables required for
XFree86/OS2 as well, which will save you from one additional reboot.
Refer to section Adding Variables to CONFIG.SYS (section 9., page 1)
below.

4. After adding the device driver entry to the CONFIG.SYS file, you must
reboot to install the driver. XFree86/OS2 will not work without this
driver.

5. Start a full screen OS/2 CMD session and enter the following command:

[C:\] Y:\XFree86\bin\SuperProbe

6. This command will (normally) report important information about your
video configuration, i.e. the type of chipset, the available video mem-
ory and the RAMDAC circuit available. Please write this down or redi-
rect the output of ``SuperProbe'' into a file by entering:

[C:\] Y:\XFree86\bin\SuperProbe >filename

7. SuperProbe can identify many more video cards than are supported by
XFree86. In some cases, SuperProbe unfortunately detects a wrong card,
often it claims to have seen a MCGA card which is some sort of a fall-
back. Generally, if it is approximately right, there are only few rea-
sons for doubts; if it is totally off (e.g. saying it has seen a
ET4000, and you have a Cirrus card), you should report a mis-detection
as a bug to the given address. In all cases, please take the few min-
utes and check the accompanying README.* files to check for special
precautions, options, or features of the card.

8. If the README files tell you that your hardware is supported, please
obtain the rest of the software.

8. Installing the packages

XFree86/OS2 assumes a directory hierarchy starting from drive:\XFree86. This
can be changed, but is strictly discouraged.

1. Choose a HPFS partition with sufficient free space.

2. For each package to install, go to the root directory of this drive,
and type:

drive:> cd \
drive:> unzip \path_of_packages\Xxxxx.zip

3. You might encounter that some packages report duplicate files, e.g.
the X server packages install corresponding README files, which are
also in the Xdoc package. This is okay, the files are the same. Let
unzip replace the files.

4. No special sequence to unpack the files is required.

9. Adding Variables to CONFIG.SYS

XFree86/OS2 requires a number of settings in the CONFIG.SYS file to work cor-
rectly. Please add the following settings, and in particular take care to set
forward versus backward slashes correctly:

TERM
Set the preferred terminal type for the xterm or editor to be
used. Some programs need this setting. I have my type set to

SET TERM=ansi

\XFree86\lib\X11\etc\termcap.x11 contains a suitable termcap
which can be used in place of termcap files that come with EMX,
EMACS, or other ported software.

TERMCAP
This variable must be set to the location where the termcap file
used for the above TERM variable is searched. My setting, for
instance, is:

SET TERMCAP=D:/EMX/ETC/TERMCAP.X11

Note that forward ``/'' is used as a directory separator.

ETC
Set to an ETC directory. Normally, this is already set to the ETC
directory of the TCP/IP code, such as

SET ETC=C:\TCPIP\ETC

For Warp 4 and later, this may point to the \MPTN\ directory.
This is okay.

TMP
Set to an TMP directory which should reside on a HPFS drive (or
other filesystem that has real long names). Often, this variable
is already set to the TMP directory of the TCP/IP code, such as

SET TMP=C:\TCPIP\TMP

If you have installed additional software, like VisualAge for
C++, it might be that this variable points to some directory
\ibmcpp\tmp .

HOSTNAME
Set to the internet hostname. Normally, this is already set by
the TCP/IP installation program, such as

SET HOSTNAME=myhost

With IAK, you would normally run a loopback configuration Network
configuration (section 10., page 1) and would then set this to

SET HOSTNAME=localhost

USER

LOGNAME
Set both to a username. Currently, they are there just to make
some programs happy; in the future, this variable might be set by
a login shell of a multiuser configuration. My variable, for
instance, is set to

SET USER=holger
SET LOGNAME=holger

HOME
Set this to an existing directory that is supposed to be a home
directory of a user. Some utilities place temporary and init
files here. This is also future investment for a multiuser con-
figuration, but must still be there. For instance, this variable
might be set to

SET HOME=H:\user\holger

X11ROOT
This is one of the most important settings, it determines the
root of the XFree86 directory tree. Normally, you will set this
to the drive letter of the partition where the \XFree86 tree
resides, such as in

SET X11ROOT=Y:

You may try to move the tree to another subdirectory, e.g. to
K:\OS2\X11\XFree86... and would then have to change this to

SET X11ROOT=K:/OS2/X11

, but this is discouraged, since some utilities might not accept
this. Note the forward ``/'' as a directory separator here.

DISPLAY
This variable may be set to the display to be used for displaying
clients. Normally you will set this variable to the same value as
the HOSTNAME variable and simply add a :0.0 after it, such as

SET DISPLAY=myhost:0.0

Read the X11 man page on the exact meaning of these postfixes and
other options.

XSERVER
Set this to the executable name of the X server to be used. This
must be a complete path. My setting, for instance, looks as fol-
lows:

SET XSERVER=D:/XFree86/bin/XF86_Mach64.exe

PATH
Add the binary directory for the X11 utilities to your search
PATH. This is normally the directory (adjust the letter)

Y:\XFree86\bin

It is possible to move the binaries to another directory in the
search path; for maintenance reasons and clarity of the struc-
ture, this is not recommended, though. You might, of course, use
a software like TVFS to redirect these files to elsewhere.

LIBPATH
Add the DLL directory for the X11 utilities to the LIBPATH. This
is normally the directory (adjust the letter)

Y:\XFree86\lib

It is possible to move the DLLs to another directory in the
library path; for maintenance reasons and clarity of the struc-
ture, this is not recommended, though. Note that Y:\XFree86\lib
has several other subdirectories; these may not be moved else-
where, rather they must stay there, because most utilities form a
path to these directories by using %X11ROOT%\XFree86\lib as a
base.

MANPATH
If you want to use xman, add the path to a set of manual pages
to this variable. This variable allows multiple directories, like
the standard PATH variable. Example:

SET MANPATH=Y:\XFree86\man;Y:\EMX\man


SET MANPATH=Y:\XFree86\man;Y:\EMX\man

Note: xman alone might not be sufficient to display arbitrary
Unix man pages correctly. You might have to install the GROFF
formatter tool as well. See FAQ for more details.

OS2_SHELL

COMSPEC

SHELL

X11SHELL
Some scripts in XFree86 rely on a shell that is compatible to the
standard CMD.EXE. CMD.EXE has some essential properties that
allows it to work correctly in an xterm. Third party shells may
not been developed with running in an environment that, like
xterm. accept input and output from the stdin/stdout file chan-
nels, but access keyboard and video services directly. The above
variables allow reconfiguration of your system in order to run
any favorite shell outside XFree86 and still have XFree86 use
CMD.EXE. See the FAQ for more details.

The recent version of XFree86/OS2 has a REXX script named checkinstall.cmd
which you can (and should) use to check whether you have entered most things
correctly. This is not bullet-proof, but prevents the most obvious setup
problems. Also, the X server itself will do some checking and will refuse to
start if something is wrong.

10. Remarks on the Network Configuration

It is beyond the scope of this document to even give an introduction about
the correct installation of the TCP/IP networking system. You must do this
yourself or seek assistance elsewhere. It is only possible to say here that a
PC working well in a TCP/IP based LAN network will also work with XFree86/OS2
(when all other prerequisites are matched as well).

With IAK, there is a special configuration necessary, unless you want to use
XFree86/OS2 only during a hot link to your Internet provider, the so called
``localhost'' or ``loopback'' configuration. This is a local network inter-
face which ``loops'' back to the same host. The following settings are neces-
sary for this:

1. Create a file \tcpip\etc\hosts with the following content:

127.0.0.1 localhost

2. Add the following line to your \tcpip\bin\tcpstart.cmd:

ifconfig lo 127.0.0.1 up

If you don't have such a tcpstart.cmd file (Warp 4 calls this file
\MPTN\BIN\MPTSTART.CMD), create one, and add a line like the following
to your config.sys file: CALL=C:\OS2\CMD.EXE /Q /C C:\tcpip\bin\tcp-
start.cmd >NUL: (implying that your bootdrive is C:).

3. Set the HOSTNAME environment variable to localhost as described in the
last section.

4. Add the following line to CONFIG.SYS:

SET USE_HOSTS_FIRST=1

5. After rebooting, verify that the following command works:

[C:\] ping localhost

You don't need this ``loopback'' interface if your PC is connected to a LAN
(either directly or through SLIP/PPP).

In case of a SLIP/PPP line, you have to establish this connection BEFORE you
start XFree86. See the next section for more details.

Note that the ability to use host names, for instance in the DISPLAY vari-
able, correlates with the existance of a name resolver. If you don't have a
LAN-based DNS server available, you have to add the relevant hostnames to
your HOSTS/ file. The TCP/IP configuration dialogue in your system configura-
tion folder allows you to edit this file. The checkinstall.cmd script coming
with XFree86/OS2 gives some advice on the configuration as well. If you have
problems to get this or other basic networking things running, seek assis-
tance in the FAQ, the xf86os2 mailing list or the mailing list archive.

11. Dynamic IP Considerations

Generally, the whole stuff works best, if your machine has a fixed IP
address. The localhost address, and also fixed (non-routable) local
addresses (10.x.x.x, 192.168.x.x, 172.16.x.x-172.31.x.x) work fine. A problem
occurs on both sides of such an X connection if there are dynamic IP
addresses involved, for instance in case of a PPP line to an ISP. Unfortu-
nately, the XFree86/OS2 net community hasn't come up with a set of helpful
scripts yet (which I would integrate), so there are here only some hints what
the problem really is: The X server listens for X protocol packets on some
defined host/port socket. It gets the information about the socket from
either the command line or the resolved hostname (which it gets from the
HOSTS file or the DNS server). Here the HOSTNAME variable comes into play.
Once the server is running, a change in the IP/HOSTNAME configuration won't
be recognized any more. Thus, the general approach for X over a dynamic IP
line is: build the connection to the ISP first, then start the server. The
relevant script that is responsible for starting the server is the startx.cmd
script which executes (indirectly) the \XFree86\lib\X11\xinit\xinitrc.cmd
script. You have to modify these scripts in order to set the HOSTNAME and
DISPLAY variables correctly and start the server with the right IP address.
The X server log shows, right to the beginning, at which IP address it is
listening, for debug purposes.

12. Configuring X for Your Hardware

After you have added the required settings and setup a working network, run
the xf86config program to create a standard configuration file in
Y:\XFree86\lib\X11\XF86Config from a windowed or full screen OS/2 text ses-
sion:

[C:\] xf86config

The xf86config program will ask a number of questions. You will need the
information obtained from the SuperProbe program here. The program should be
self explanatory; if you have problems to understand something though, seek
assistance in the newsgroups.

It is possible, but strongly discouraged for the non-expert, to edit the
XF86Config file with a text editor. In a few situations as described in the
FAQ, however, this might even be mandatory. This file is not a hacker's area,
such as the Win95 registry, but it has in common with it that you can easily
cause damage.

For details about the XF86Config file format, refer to the XF86Config(4/5)
manual page.

If you know the configuration process from Linux or other XFree86 platform,
you will encounter a few differences:

o There is no configuration for the mouse type or device. The mouse device
name is fixed to OSMOUSE, and this cannot be changed. If you have a
three-button-mouse, install the correct OS/2 driver for it, such as

DEVICE=D:\OS2\BOOT\PCLOGIC.SYS SERIAL=COM1
DEVICE=D:\OS2\BOOT\MOUSE.SYS TYPE=PCLOGIC$

for a MouseSystems compatible mouse, for instance.

o The X server does not read the native OS/2 keyboard map, but the new XKB
server extension might already give you a correct keyboard layout, pro-
vided your language was selectable in the xf86config program. If you
encounter incorrect settings, please send a mail to XFree86@XFree86.org
describing in detail what is wrong. Even with XKB, you have the option
to replace some key settings with a xmodmap file. See the man page for
xmodmap for details (or use some available xmodmap file from Linux -
they are the same).

o There is no support for the Wacom and Elographics input devices yet.

In most cases, an existing XF86Config file for the same XFree86 version from
Linux or another platform may be used without changes. There are two promi-
nent exceptions: some S3 805 based VLB cards put their video memory in odd
locations, and there seems to be an unresolvable PM driver inconsistency with
Matrox cards.

For S3 VLB cards, the X server can search for this memory by experimentally
mapping and unmapping possible memory regions. However, in XFree86/OS2, the
OS may run out of memory tiles during this process. If this happens, you must
find out the location of the memory yourself and add it as an option

MemBase 0x12345678

to the section "Device" of your XF86Config file.

For Matrox cards, the X server may fail to detect the PCI ID of the card cor-
rectly, as the PM driver and Matrox BIOS may have reprogrammed the card's PCI
configuration in a non-standard way. The server will then fall into a VGA
compatible mode at 320x200 resolution. To prevent this, add a

PCIProbe2

to the section "ServerFlags" of your XF86Config file.

Once you've set up a XF86Config file, you can fine tune the video modes with
the xvidtune utility. Note this is an X11 program which has to be executed in
a local xterm window of a running X server, not in a PM window.

13. Running X

16mb of memory is a recommended minimum for running the network software, X
and the presentation manager in parallel. The server, window manager and an
xterm take about 4-6 Mb of memory themselves. X will start up on a system
with 8MB or less, but the performance will severely suffer from heavy disk
swapping. Your mileage may vary, though, so some people might consider this
still tolerable.

Some more on resource requirements: With the arrival of complex desktops like
WindowMaker, KDE, Gnome, Enlightment, etc. which add a lot of graphical fea-
tures, resource requirements grow. The X server will cache used fonts and
resource settings internally, and depending on the number of windows (back-
ing- store) it may require much more memory and swapspace than the mentioned
few MBs. Also take into consideration that X runs in parallel to PM which
also takes its share. My own system, albeit meanwhile rather outdated, is a
PII-233 with 128MB, however, it is a development system. 64 MB are meanwhile
standard, and okay for the purpose, and my laptop runs Aurora with XFree86 in
32MB, as well.

The easiest way for new users to start X windows is to type:

startx

in a PM CMD window. People have reported problems when starting this in a
fullscreen session or through a remote telnet session, so don't try it.

To get out of X windows, type: ``exit'' in the console xterm. You can cus-
tomize your X by creating .xinitrc, .xserverrc, and .twmrc files in the
directory that the HOME environment variable points to. These files are
described in the xinit and startx man pages.

By default, the systemwide xinitrc file (in Y:/XFree86/lib/X11/xinit/xini-
trc.cmd) installs the rather simplistic twm window manager. You can find bet-
ter window managers on the ported software page at
.

14. Rebuilding the XFree86 Distribution

Do you really want to rebuild XFree86/OS2 from source? Read the file

on details to recompile XFree86/OS2 from scratch.

15. Building New X Clients

The easiest way to build a new client (X application) is to use xmkmf if an
Imakefile is included in the sources. Type ``xmkmf -a'' to create the Make-
files, check the configuration if necessary and type ``xmake''. ``xmake'' is
a wrapper for the GNU make program which defeats the improper SHELL setting
typically found in a Makefile generated from an Imakefile. Also see the
XFree86/OS2 FAQ for more hints about porting X clients.

16. Acknowledgements

Many thanks to:

o Sebastien Marineau for his great work on getting the server code
debugged

o Eberhard Mattes for the wonderful base platform EMX which this port
heavily relies on

o ME - no, no, forget this: I won't praise myself :-)

Generated from XFree86: xc/programs/Xserver/hw/xfree86/doc/sgml/OS2.sgml,v 3.9.2.11 1999/12/20 12:55:51 hohndel Exp $

$XConsortium: OS2.sgml /main/4 1996/03/11 10:46:06 kaleb $

"


$XFree86: xc/programs/Xserver/hw/xfree86/doc/README.OS2,v 3.13.2.14 1999/12/20 16:37:01 hohndel Exp $