Äîêóìåíò âçÿò èç êýøà ïîèñêîâîé ìàøèíû. Àäðåñ
Äàòà èçìåíåíèÿ: Tue Mar 29 22:25:51 2016
Äàòà èíäåêñèðîâàíèÿ: Sat Apr 9 23:12:16 2016
Along with the privilege of having full access to the AAAPòÀÙs telescopes and observatory facilities, all keyholders must participate in the AAAPòÀÙs public observing programs, and are expected to contribute to occasional maintenance and work sessions at the observatory.
Each keyholder will be assigned to a public observing duty team of approximately four keyholders. Each team will have one team leader. The leader and his/her team will have full responsibility for operation of the observatory and for public interactions during the public observing sessions. Each team will serve their duty on a rotating schedule of the designated public observing nights. Keyholders unable to attend their particular duty night are requested to find a replacement for themselves by polling their fellow keyholders and switching duty nights.
The current public observing schedule opens the first Friday night in April, and continues each Friday night through the end of October. The schedule is published in the SIDEREAL TIMES and on the clubòÀÙs website (princetonastronomy.org).
Keyholders are ambassadors of the AAAP to the public. Patience must be exercised and respect shown when responding to the various questions and situations that arise when the public is on the premises.
Be prepared to direct the flow of people through the observatory and the grounds when there are large groups. Be aware of traffic and the status of parking to maintain good control. Keyholders are expected to be knowledgeable about astronomy and our equipment, and to be able to communicate basic astronomical and telescope principles to the public.
Please use the opportunity to educate and entertain as appropriate for the size and age of the audience. Communicate the need for red light use in the observatory, the definition of light pollution and how homeowners can minimize light pollution by using appropriate outdoor lighting.
It is suggested that the observing team agree in advance on a list of desirable objects to show the public. These should include a mix of the best Messiers plus planets and moon as appropriate. Since many people stay for only a brief period, it is advisable to rotate through a list of prime objects a few times during a nightòÀÙs session.
During non-public observing sessions or when conducting daytime activities at the observatory, keyholders should handle public inquiries by briefly describing the observatory and AAAP club membership benefits. Be sure to point out the current public observing schedule. Always be polite when turning away uninvited visitors, however, it is your option to provide a few observations to them if conditions allow.
There are three, lockable gates between the park entrance at Bear Tavern Road (Rt. 579) and the observatory. Typically, only two of the three gates are locked, depending on seasonal use of the park.
The first gate is at the Phillips Farm park entrance at Bear Tavern Road. The second gate is at the end of the asphalt parking area (beyond the soccer fields) near the camping area. The third gate is after the gravel road which goes past the camp sites, before returning to Brickyard Road within the park.
Recent security problems in the park dictate that the following procedures be followed at all times by all keyholders. FAILURE TO FOLLOW THESE PROCEDURES WILL RESULT IN LOSS OF KEYHOLDER PRIVILEGES.
Each gate, if locked, is secured in an identical fashion: a length of chain is run through the gate latch with the parkòÀÙs lock on one end and the AAAPòÀÙs lock on the other end. When securing a gate it is to be locked only in this way. DO NOT ATTEMPT TO LOCK ANY GATE BY ATTACHING THE AAAPòÀÙS LOCK DIRECTLY TO THE GATE LATCHòÀÔTHIS IS NOT ACCEPTABLE TO THE STATE PARK RANGERS.
If a keyholder enters the park to use the observatory on any night other than a designated public night they must make note
of which of the three gates were locked, and re-secure those gates in the same manner as found upon entering the park
and after leaving the park. The gates must not be left open.
It is also not sufficient to close the gate but leave the lock on the chain unlocked or locked with one number
shifted on the lock for easy egress from the park after an observing session is finished. The gate must be locked and all of the
numbers spun on the lock so that anyone who comes by cannot easily guess the combination and gain access to the park.
This procedure must be applied to all locks.
This procedure must be applied to all locks. It is not sufficient to lock the Bear Tavern Road/Rt. 579 gate (typically locked during the winter months) but leave the other two open, all gates must be locked. The only deviation from the above procedure is if there are campers in the park, especially in campsite D near the last gate. The campers need access to the park and therefore the first two gates must be left open. However, the last gate must always be secured on a non-public night.
It is the duty of the first keyholder to enter the observatory on a given night to note the state of the gates and communicate this information to any other keyholders who arrive at the park later. If you plan to stay at the observatory later than the keyholder who first opened the observatory, make sure that you find out the status of the gates before he/she leaves.
On designated public nights all three gates may be left open to facilitate entry of the public to the park. However, all gates must be locked and secured no later than 11:30 PM. This means that if there are still members of the public present at the observatory who do not wish to leave by 11:30 PM they will be locked in the park until a keyholder leaves and secures the gate(s) behind him/her. At 11:30 PM a keyholder must leave the observatory to secure and lock all three gates. (If there are campers in the park only the last gate needs to be locked and secured.)
If during entry you are stopped by a park ranger or (on non-public nights, particularly off-season) by township or State police, identify yourself as a member of the AAAP Club and assure the police that you have authority from the Washington Crossing State Park to be on the premises. Always be polite if you are stopped.
We realize that the above procedures will be an inconvenience to many keyholders, but they must be followed if we are to maintain the good will of the park administration.
Plug in and power-up the computer and monitor dedicated for the C14 in the Computer Room. Open The Sky software.
Locate eyepiece case and place on work desk.
Remove lens caps from C14, finderscope, eyepiece holder and place in a safe location on the work desk.
Check operation/battery power of Telrad on C14. Note dead batteries in log. Replace batteries if necessary.
Check that eyepiece holder on C14 is securely attached to back of telescope.
Install an eyepiece such as the 31mm Nagler in the eyepiece holder on the C14. ALWAYS PUT ONE OF THE HEAVIER EYEPIECES IN THE C14 BEFORE FIRST POWERING UP AND SLEWING THE MOUNT TO MAINTAIN PROPER BALANCE.
Plug-in Paramount power cable and switch on mount.
Plug in and power-up the computer and monitor dedicated for the refractor. Open The Sky software.
Remove the brass lens cap from the front of the refractor.
Place the gray 6" dew shield on the front of the refractor.
Remove film canister from refractor diagonal.
Check that eyepiece holder on the refractor is securely attached to back of telescope.
Install an eyepiece such as the 55mm Plossl in the eyepiece holder.
Plug-in Paramount power cable and switch on mount.
Turn on Telrad.
Enjoy your evening by locating and viewing a number of objects around the sky.
Always warn others before slewing the telescopes.
Be prepared to cancel any slew if the telescope mount makes strange noises or if it starts on a path pointing towards the ground. Slews can be cancelled from within The Sky software or by moving the joystick on the hand control.
a slew manually via the hand control, return the scope to a known position and re-sync the mount in the software. Then, test for safe operation by slewing first to another near-by object. Continue viewing objects only if the software and mount have been re-synced properly.
If cancelling a slew via The Sky software fails, POWER OFF MOUNT immediately to avoid damage to mount or scope. You will then need to restart the mount and software before continuing.
Continue to check for secure attachment of diagonal and eyepiece throughout the session, especially when switching eyepieces. Note any irregularities of operation in log book; similarly, share any special observations or new astronomical finds in the log.
Check to be sure fellow observers are clear of telescope before moving it to park position.
Click on an object to open the object information pop-up if necessary.
Select the Telescope Tab.
Call out "Parking Telescope" and click on Park. Alternatively, you can do this from the top menu in The Sky software by selecting Telescope->Options->Park.
Keep your eye on the scope until it is safely parked in a horizontal position being prepared to cancel its motion should anything go amiss. Exit from The Sky.
Shutdown the computer using the shutdown menu found under "Start" in the lower left corner of the screen.
Power off and unplug the computer when you see message indicating this is safe. Power off and unplug computer monitor.
TURN OFF TELRAD BY PLACING TOGGLE SWITCH (THREE POSITION SWITCH) IN CENTER OFF POSITION.
Remove eyepiece and return to case. If dew has formed or if it is exceptionally humid, always dry off the eyepieces using the heat gun (hair dryer) before putting into case. Cap all eyepieces, close case and return to shelf.
Locate all lens caps and re-install on scope and finderscope. If it is exceptionally humid, blow hot air from heat gun into the open dew cap end of the C14 before covering for the night.
When finished using the camera, be sure to perform the camera Park (shutdown) procedure, as follows, from within the Mallincam Xterminator Control software.
Click on the òÀÜConfigòÀÝ tab along the top menu bar.
Click òÀÜParkòÀÝ button in the lower left corner of the screen. Wait until a popup window appears indicating it is safe to shut down the camera and software.
Call out "Slewing or Parking Telescope" and click on Park (alternatively you can do this from the menu by selecting Telescope->Options->Park from the top menu of The Sky.
Close the popup window and exit software by clicking on the òÀÜXòÀÝ at the top right corner of the software.
Unplug the camera power supply and monitor.
Replace the wood lens cap back onto the dew shield at the front of the scope.
Turn off and unplug heater in computer room. Turn off audio equipment, if used, in computer room. Turn off red lights and turn on white light in observatory.
Check and be sure both telescopes are parked in a safe horizontal position.
Crank the roof closed watching carefully to make sure it clears BOTH telescopes.
Secure all 4 turnbuckles at the corners of the observatory.
Tidy up everything and secure trash cans. Remove all personal items from the observatory. Close bathroom door.
Check time and note closing hour and final comments in the log.
Activate the alarm.
Turn off the main light switch and be sure computer room lights are off. Close computer room door and exit observatory.
Lock the door to the observatory (BOTH LOCKS)!
Contact Observatory Chair if you found ANY problems at the observatory. Follow the gate locking procedure when exiting the park.