Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.asc.rssi.ru/RadioAstron/publications/articles/cr_2015,53,226.pdf
Дата изменения: Tue Jun 9 10:31:34 2015
Дата индексирования: Sat Apr 9 23:56:51 2016
Кодировка:

ISSN 0010 9525, Cosmic Research, 2015, Vol. 53, No. 3, pp. 226229. © Pleiades Publishing, Ltd., 2015. Original Russian Text © V.E. Yakimov, 2015, published in Kosmicheskie Issledovaniya, 2015, Vol. 53, No. 3, pp. 242245.

Creation and Development of the Software Complex for Scheduling Observations in the RadioAstron Project
V. E. Yakimov
Astro Space Center of the Lebedev Physical Institute, Russian Academy of Sciences (FIAN ASC), Leninskii pr. 54, Moscow Russia e mail: yakimov@asc.rssi.ru
Received December 16, 2013

Abstact--In preparation for launching the space radio telescope as a component of the groundspace radio interferometer (the RadioAstron project) software was developed for scheduling observations of radio sources. A set of instruments was produced for solving various tasks of modeling the space mission in the con text of radio interferometry with super long bases when a radio telescope is launched into space. The software structure and applications are described that allow scheduling observations of sources by means of a ground space radio interferometer. DOI: 10.1134/S0010952515030089

1. INTRODUCTION In the last decade of the last century the develop ment of two projects of groundspace interferometers in Russia (RadioAstron) and in Japan (VSOP) gave rise to the problem of producing software for various tasks of modeling the conditions of observation with using these interferometers. Such software packages were developed in Russia, the USA, Canada, and Hungary. These ones are as follows: ASTRON, RASS (L.I. Gurvits, V.E. Yakimov, FIAN ASC, Russia), Fakesat (D.W. Murphy, Jet Propulsion Laboratory, USA), RPIS (A.R Taylor, University of Calgary, Can ada) and SPAS (I. Fejes, SGO, Hungary) [13]. The specificity of radio interferometers with a tele scope launched into space claims specific require ments for scheduling and performance of observations with this instrument. In order that all elements of an interferometric system operate properly and effi ciently, it is necessary that, during observations, a par ticular set of conditions is fulfilled related to the orien tation of a space telescope and other devices on board the satellite, as well as to ground based supporting means related to them. In the case of the RadioAstron interferometer these conditions were discussed in detail in the paper [4]. The consideration of con straints represents a very important part of the software functional for scheduling observations with the groundspace interferometer. When the space radio telescope of the RadioAstron project was prepared for launching into space, two packages were used for solving various tasks related to observation modeling--the RASS (RadioAstron Scheduling Software) and the Fakesat. While having almost identical functionality, these packages differed in one important aspect. The RASS software package

has been produced and developed to solve various tasks of modeling predictable situations that could arise at implementing the RadioAstron project. For this reason, the emphasis was placed here on the pos sibility of detailed analysis of the configuration of all interferometer's components. The Fakesat package was produced as an instrument to aid the observer in scheduling observations of a radio source studied by means of the groundspace radio interferometer. In this connection, the package was equipped with sev eral visual means to facilitate preparing the application for scheduled observations. The Fakesat package was produced at the Jet Pro pulsion Laboratory for operation on computers of SUN/Hewlett Packard/DEC companies under the guidance of OC Solaris/HP UX/Open VMS. This package was written in a Fortran programming lan guage dialect that was not supported by the ANSI f77 Standard. In the course of practical work with the Fakesat package at the Astro Space Center there arose the need to improve it in order that the package could be used on computers running with the Linux opera tion system. However, the direct compilation of the original code with using the g77 compiler was impos 1 sible for the above reasons. So, in 1999 the package was modernized with the purpose of installing it on computers running OC Linux. The next important stage of modernizing the RASS and Fakesat packages was associated with transferring, in the RadioAstron project, into the orbit with the space radio telescope's period of revo
1

Promyslov V.G., Yakimov V.E., and Sergeev A.N., Moderniza tion of the Fakesat software package (JPL) for modeling radio sources observations with using the groundspace radio inter ferometers. // FIAN ASC Science technological report, 1999.

226

CREATION AND DEVELOPMENT OF THE SOFTWARE COMPLEX

227

lution within 89 days and high apogee. This cir cumstance demanded deep restructuring of packages both at the algorithmic level and at the level of the means for visualizing the final results of packages operation. In the case of the Fakesat package this work was done by V.I. Zhuravlev, the ASC specialist [5]. The RASS package has undergone many modifica tions in the process of using it for solution of a variety of modeling tasks within the framework of the project. In fact, the new software package was produced for solving modeling tasks in the astronomy: SSAM-- Software System for Astronomical Modeling. In this new package the following principles of code organi zation were implemented: modularity, extensibility and possibility of generating binary files of the applica tions for the Linux and MS Windows operation sys tems, virtually on the basis of the same code base with the exception of calls of system functions. In addition, the package made it possible to read the initial data in a free format regardless of the type of their representa tion in the input stream. One can acquaint with the package in more details on the information resource of the RadioAstron project: webinet.asc.rssi.ru/software/ AstroCom. 2. DESCRIPTION OF THE SSAM SOFTWARE COMPLEX On the top level the complex consists of two direc tories, namely data and AstroCom. The first directory contains many subdirectories with initial data for var ious applications, as well as subdirectories for the final results of their work. The second directory contains, in essence, the "engine" of the complex, and it includes the command shell, the applications developed within the SSAM complex framework, and the set of libraries. There may also be two additional subdirectories: bin and lib for external applications and the scripts subdirectory for scenarios. External applications and scenarios, if neces sary, run in the AstroCom under the guidance of the analog of a command shell, which represents, in essence, one of the internal applications of the complex. Any application developed for the SSAM complex, at the top level has an identical structure that includes two configuration files, the main program file written on the standard ANSI f77 language, and the set of libraries that specify the application functional. The Fortran 77 programming language was used for the purpose of compatibility with the extensive library of programs for scientific research developed in previous years. In the case of generating applications for the MS Windows operating complex, the main program may contain extensions to the language standard typi cal for the Fortran Power Station compiler. The names of configuration files are identical in every application: "app.cfg" and "task.ini." Both files are text ones with the lines, which contain the data required for configuration and determination of the
COSMIC RESEARCH Vol. 53 No. 3 2015

current state of the application. The data representa tion format is typical for configuration files: "key = value" or "key = value_1 value_2 ...value_n." The data type in the "key" variable is text one. The admis sible types for the "value" variable are text, integer or real (of double precision), which are placed in a line without restrictions on the position and order of suc cession. To optimize the reading of configuration files, lines with keys can be arranged into sections. The "app.cfg" file contains global actual parame ters that define the work of the application as a whole. In addition, this file may indicate the state of the appli cation for the current task specified by the "task.ini" file. For example, having selected the key value of "mode = ground," "mode = space," or "mode = ground + space" in the "app.cfg" file of the zROSSAT application (see below), the task will be solved for the ground based network of radio telescopes, for the space segment or for the groundspace radio interfer ometer as a whole, respectively. The "task.ini" file includes the actual parameters for the current task. The application file in the Fortran 77 language contains only the main program and several auxiliary programs that define the specific features of the appli cation. And, again, as in the case of configuration files, all applications have, structurally, nearly identical main programs; the only distinction consists in calls of procedures from the additionally loaded libraries, which just determines the functional of a particular application. Each application contains reusable code at the level of the main program. Unification of struc tures of various applications facilitates their support ing throughout the life cycle and the development of new applications. And the last thing that should be mentioned in the general description of the SSAM software complex is the rules of attributing the names of applications inside the AstroCom directory. The name of any application, which has a meaningful sound determined by the application specificity, contains the prefix in the form of one of symbols: x, y or z. Prefix x in the application name indicates that it possesses the graphical user interface or GUI. Only one application, namely yash, has the prefix y in its name. This is a special applica tion, the command shell, under guidance of which one can run to operation several applications in the pack age mode. Prefix z in the name indicates that this application uses a command line interface, or CLI. 3. SCHEDULING THE OBSERVATIONS IN THE RADIOASTRON PROJECT The zROSSAT application of the SSAM software complex represents a natural development of the RASS package within the framework of the new approach to developing software for scheduling observations. The scheduling of radio sources observations with using the groundspace RadioAstron interferometer, as it was presented in the pre launch project prepara

228

YAKIMOV

tion period, consists of several stages. The initial and final stages of the scheduling procedure are described below. These stages are sufficient in the case of the so called standard mode of a scheduling procedure. In the exceptional, atypical cases of the groundspace radio interferometer configuration, there arises the necessity in the detailed analysis of the conditions of studied source visibility by various interferometer's systems, and in developing the acceptable scenario of performing observations. For this purpose the zROS SAT application possesses special options that are specified in the "app.cfg" file. At the first stage of scheduling, for the date speci fied in the "task.ini" file, the whole celestial sphere or a part of it is looked through. The corresponding option and the necessary parameters are set in the "app.cfg" file. Here it is worth it to comment on the style of output files containing intermediate or final results of any application of the SSAM complex. Typ ically, these files are accompanied by a header with text information explaining the sense of the obtained result. It is important to note that the result of any application can serve as the initial data to process by another application. The software package possesses the appropriate means. In the nodes of the celestial sphere's grid, defined by the equatorial coordinates RA/Dec, are repre sented the time intervals in hours, during which the operation of the space segment (the space telescope and one of related science data receiving stations) of the RadioAstron interferometer is possible. One should emphasize that this option allows one to reveal the possibility of observing the source with RA/Dec coordinates only. The fact is that, at this stage, one takes into account only the constraints on the position of the Sun and the direction to the working data receiving station on the Earth, which are determined by the orientation of the space telescope observing the source under study. These constraints are most signif icant ones from the long list presented in the Protocol of functional constraints [4]. At the next scheduling stage the zROSSAT applica tion is fulfilled for the chosen source. Its equatorial coordinates are specified in the "task.ini" file. In addi tion, this file includes the date of observation (start and end), the name of the file containing the state vec tors of the predicted orbit of a space telescope for the time interval including the scheduled observation, as well as the names of stations receiving scientific data and the ground based radio telescopes selected for participation in the joint work. The key information at this stage is the time inter val, when the space radio telescope can work jointly with the science data receiving station in Pushchino or Green Bank (USA). If the observation of the chosen source by a space telescope at the given date is con firmed, then one should search for joint time intervals, when the source is visible both by space and ground based radio telescopes. This searching can be done

either visually (the corresponding file is generated by the application), or by means of software. If the source is not visible by the space based radio telescope (though at the first stage it was found that the source could be observed for the incomplete set of con straints), the means for clarifying the reason of the lack of visibility are provided in the zROSSAT application. For the majority of configurations (the mutual positions of a studied source, the Sun, Moon, and Earth, the possibility of participation of selected ground based radio telescopes in the joint work with the space segment of a radio interferometer) it is suffi cient to take into consideration the constraint on the position of the Sun and find out whether the commu nication with any scientific data receiving station does really exist. In these cases the second stage is the last one in the scheduling procedure. In the prelaunching period of the RadioAstron project preparation a great number of tasks on model ing radio sources visibility had been performed with regard to all constraints formulated in the Protocol [4]; and, further, the comprehensive testing of the soft ware complex was performed in collaboration with the staff of the Lavochkin Research and Production Asso ciation (the Lavochkin RPA). Before the space telescope launching, the choice of the optimal orbit was performed by the criterion of sci ence research efficiency based on calculation of radio sources visibility conditions for the whole celestial sphere over a period of a year.2 According to the results of analysis, it was found out that the situation is extremely undesirable for the project when the inter ferometric observations have fallen on the June August period. According to the flight test schedule, the interferometric stage should occur in 2 months after launching the space telescope. Thus, the favorable launch window lies within the JuneAugust intervals. The choice of the launch date within this interval pro vides best conditions for efficient performing the scien tific program of observations during a year. CONCLUSION In the course of preparation to launching the space radio telescope as a component of the groundspace radio interferometer, software was developed for scheduling observations of radio sources. Actually, the set of instruments (the so called toolkit) was produced for solving various tasks of modeling the space mission in the context of radio interferometry with super long bases, when one or several telescopes were launched into space. This set of instruments can be used for developing new applications, because the SSAM software com
2

Yakimov V.E., Popov M.V., Litovchenko I.D., and Sheikhet A.I., Choice of the optimal orbit by the criterion of science research efficiency in accordance with the launch window // FIAN ASC Science technological report, 2011. COSMIC RESEARCH Vol. 53 No. 3 2015

CREATION AND DEVELOPMENT OF THE SOFTWARE COMPLEX

229

plex is based on the principles of modularity, extensi bility and code reuse. And, from this point of view, the complex represents a framework for developing appli cations for solving a wide range of tasks--from the analysis of an arbitrary text in the input and/or output data stream up to model calculations with different degree of complexity. The structures of any applica tions at the top level, the types of configuration files, and the main program are virtually identical. The functional of applications is determined exclusively by the choice of existing or newly developed libraries. Possible perspectives of use and development of the software complex are defined by the current tasks of the RadioAstron project on the basis of existing appli cations and generating new ones, if necessary. The SSAM software complex can be used for analysis and modeling of new space missions projected to solving astrophysical problems with regard to instruments' location in near and far space. ACKNOWLEDGMENTS The author would like to thank V.G. Promyslov for understanding and support in the work on the software complex. The author is grateful to A.I. Sheikhet and E.N. Philippova from the Lavochkin RPA for positive attitude and patience during the long term testing of the complex in the pre launching period of the project preparation. The RadioAstron project is completed by the Astro Space Center of the Lebedev Physical Institute of the Russian Academy of Sciences and by the Lavochkin

RPA under contract with the Russian Space Agency, in collaboration with many sciencetechnological organizations in Russia and other countries. REFERENCES
1. Murphy, D.W., ASC simulation software develop ments, Interoffice Memorandum of the Jet Propulsion Laboratory, USA, 1993, pp. 115. 2. Fejes, I., Murphy, D.W., Taylor, A.R., et al., Space VLBI user assistance software. in VLBI Technology: Progress and future observational possibilities: Proc. of the Intern. Symposium held at Kyoto Intern. Conf. Hall on September 610, 1993, Tokyo: Terra Scientific Pub lishing Company, 1994. 3. Murphy, D.W., Yakimov, V., Kobayashi, H., et al., Space VLBI simulations, in VLBI Technology: Progress and future observational possibilities: Proc. of the Intern. Symposium held at Kyoto Intern. Conf. Hall on Septem ber 610, 1993, Tokyo: Terra Scientific Publishing Company, 1994. 4. Voinakov, S.M., Filippova, E.N., Sheikhet, A.I., and Yakimov, V.E., Functional restrictions on the orientation of onboard and ground methods in the RadioAstron project, Kosm. Issled., 2014, vol. 52, no. 5, pp. 408414. [Cosmic Research, p. 373.]. 5. Zhuravlev, V.I., The Fakerat software package in the RadioAstron international interferometric project with very long groundspace basesge in the st results of observations, Kosm. Issled., 2015, no. 3.

Translated by Yu. Preobrazhensky

COSMIC RESEARCH

Vol. 53

No. 3

2015