Документ взят из кэша поисковой машины. Адрес оригинального документа : http://www.adass.org/adass/proceedings/adass99/P2-33/
Дата изменения: Wed Oct 11 04:33:44 2000
Дата индексирования: Tue Oct 2 06:29:15 2012
Кодировка:

Поисковые слова: arp 220
SDImager: An Imaging Tool for Single Dish Observations in AIPS++ Next: DISH: The Single Dish Environment in AIPS++
Up: User Interfaces, Visualization, Data Acquisition and Reduction
Previous: I/O Performance of AIPS++
Table of Contents - Subject Index - Author Index - PS reprint -

Garwood, R. W., Cornwell, T. J., & McMullin, J. P. 2000, in ASP Conf. Ser., Vol. 216, Astronomical Data Analysis Software and Systems IX, eds. N. Manset, C. Veillet, D. Crabtree (San Francisco: ASP), 494

SDImager: An Imaging Tool for Single Dish Observations in AIPS++

R. W. Garwood, T. J. Cornwell, J. P. McMullin
NRAO1, 520 Edgemont Road, Charlottesville VA 22903

Abstract:

We present the SDImager tool which is designed to be the single dish imaging component of DISH in AIPS++. The initial SDImager tool provides a suite of tools to examine and image traditional position-switched observations. Recent work has concentrated on developing an imaging tool for single dish on-the-fly (OTF) observations using the same imaging class library as used for synthesis imaging in AIPS++.

1. Traditional Single Dish Mapping

Traditional single dish mapping techniques involve pointing the telescope at regular grid points covering the region of interest and integrating at each point until the desired signal to noise ratio is achieved. The initial single dish imaging tool in AIPS++ provides a few tools to examine and image these types of observations.

Three functions are available in the SDImager tool in the first release of AIPS++.

lookmap
This is intended as an aid while observing. Crosses or scan identification numbers are indicated at the relative positions of each scan.
spectramap
Spectra are plotted at their relative spatial locations as shown in Figure 1.
contourmap
A simple contour map of the peak values along each line of site is displayed.
All of these tools use the DISH plotter and are intended to be used as a complement to the rest of the DISH environment in AIPS++ (Garwood & McMullin 2000).

Figure 1: Spectramap Tool Showing NRAO 12m Data Towards W49N.

Future work with these tools will be focussed on improving the interface to make them more automatic (requiring fewer parameters). Two additional functions are planned.

clumpfind
This is envisioned as being a tool to find clumps in a data cube.
otfmap
This will be the interface to the single dish imaging described in the next section.

2. Imaging Single Dish On-the-fly Data in AIPS++

In order to increase the yield of single dish telescopes, OTF observing techniques have been implemented. These techniques optimize mapping efficiency and improve calibration over the mapped field by rapidly scanning across the region of interest. The resulting data, which has not been observed at regular grid points, must then be gridded to produce an image.

The results shown in Figure 2 are from recent work in AIPS++; these tools are not yet available in an AIPS++ release. The data used are from an OTF observing run at the NRAO 12m telescope taken towards the same source used in the previous section of this paper. The initial calibration, done before the image was constructed, used off-source integrations taken at the end of each OTF pass across the region.

The image was constructed using the same framework as is used for synthesis imaging in AIPS++. The only required change was the addition of a C++ class responsible for the actual gridding of the single dish measurements. The design of the AIPS++ calibration and imaging system is described in Cornwell & Wieringa (1997).

Removal of artifacts due to gain drifts was accomplished by fitting and subtracting baselines. This was done using a simple Glish script that called on the functions of the AIPS++ image tool and the AIPS++ polynomial fitter. Figure 2 shows an image of the peak values from the final gridded image. It is displayed using the AIPS++ viewer.

DISH and the SDImager tools described in the previous section of this paper can be used to examine the individual spectra in the gridded image. A plot using the spectramap function and select spectra from the OTF image is shown in Figure 3.

Our next goal is to implement the calibration steps using the AIPS++ calibration classes and to combine OTF data with synthesis observations.

Figure 2: AIPS++ Viewer Showing Peak Intensity of Image of OTF Data.
\begin{figure}
\epsscale{0.80}
\plotone{P2-33b.eps}
\end{figure}

Figure 3: Spectramap Tool Showing Select Scans from the OTF Image.

References

Cornwell, T. J., & Wieringa, M. H. 1997, in ASP Conf. Ser., Vol. 125, Astronomical Data Analysis Software and Systems VI, ed. G. Hunt & H. E. Payne (San Francisco: ASP), 10

Garwood, R. W., & McMullin, J. P. 2000, this volume, 498



Footnotes

...NRAO1
The National Radio Astronomy Observatory is a facility of the National Science Foundation operated under cooperative agreement by Associated Universities, Inc.

© Copyright 2000 Astronomical Society of the Pacific, 390 Ashton Avenue, San Francisco, California 94112, USA
Next: DISH: The Single Dish Environment in AIPS++
Up: User Interfaces, Visualization, Data Acquisition and Reduction
Previous: I/O Performance of AIPS++
Table of Contents - Subject Index - Author Index - PS reprint -

adass@cfht.hawaii.edu